blue88128 发表于 2009-5-26 18:55:35

谁能帮忙给看看,谢谢!急!

# skyeye -e linux-2.4.x/linux
...................................

zone(0): 0 pages.
zone(1): 3072 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0
Calibrating delay loop... 15.82 BogoMIPS
Memory: 12MB = 12MB total
Memory: 11004KB available (919K code, 180K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Atmel USART driver version 0.99
ttyS0 at 0xfffd0000 (irq = 2) is a builtin Atmel APB USART
ttyS1 at 0xfffcc000 (irq = 3) is a builtin Atmel APB USART
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 1C00000-1D2EFFF (RO) <ROMFS>
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
SkyEye NE2k Ethernet driver version 0.2 (2003-04-27)
sene2k dev name: eth0: <6>Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (romfs filesystem) readonly.
Shell invoked to run file: /etc/rc
Command: hostname GDB-ARMulator
Command: /bin/expand /etc/ramfs.img /dev/ram0
Command: mount -t proc proc /proc
mount: /etc/mtab: Read-only file system
Command: mount -t ext2 /dev/ram0 /var
mount: /etc/mtab: Read-only file system
Command: mkdir /var/tmp
Command: mkdir /var/log
Command: mkdir /var/run
Command: mkdir /var/lock
Command: mkdir /var/empty
Command: cat /etc/motd
Welcome to
          ____ __
      /__| ||_|               
    __| || | _ ________
| | | | || || |_ \| | | |\ \/ /
| |_| | |__| || | | | | |_| |/    \
|___\____|_||_|_| |_|\____|\_/\_/
| |
|_|

GDB/ARMulator support by <[email protected]>
For further information check:
http://www.uclinux.org/

Command: /bin/ifconfig eth0 up 10.0.0.2
Execution Finished, Exiting

Sash command shell (version 1.1.1)
/> ifconfig
eth0      Link encap:EthernetHWaddr 02:00:00:00:00:00
          inet addr:10.0.0.2Bcast:10.255.255.255Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
          Interrupt:16

/> ifconfig lo 127.0.0.1 up
/> ifconfig
eth0      Link encap:EthernetHWaddr 02:00:00:00:00:00
          inet addr:10.0.0.2Bcast:10.255.255.255Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
          Interrupt:16

lo      Link encap:Local Loopback
          inet addr:127.0.0.1Mask:255.0.0.0
          UP LOOPBACK RUNNINGMTU:16436Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)

/> ping 10.0.0.2 -c 4
PING 10.0.0.2 (10.0.0.2): 56 data bytes
64 bytes from 10.0.0.2: icmp_seq=0 ttl=64 time=5.5 ms
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=0.-6 ms
64 bytes from 10.0.0.2: icmp_seq=2 ttl=64 time=0.-6 ms
64 bytes from 10.0.0.2: icmp_seq=3 ttl=64 time=0.-6 ms

--- 10.0.0.2 ping statistics ---
4 packets transmitted, 4 packets received, 0% packet loss
round-trip min/avg/max = 0.-6/0.9/5.5 ms
/> ping 127.0.0.1 -c 2
PING 127.0.0.1 (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.-7 ms
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.-6 ms

--- 127.0.0.1 ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.-7/214748364.1/0.0 ms
/> route
Kernel IP routing table
Destination    Gateway      Genmask      Flags Metric Ref    Use Iface
10.0.0.0      *            255.0.0.0      U    0      0      0 eth0
/> ping 10.0.0.1 -c 2
PING 10.0.0.1 (10.0.0.1): 56 data bytes


到这就停住了,这是uclinux的,下面是主机的:


# ifconfig
eth0      Link encap:EthernetHWaddr 00:E0:4C:BC:C5:BA
          inet addr:192.168.111.111Bcast:192.168.111.255Mask:255.255.255.0
          inet6 addr: fe80::2e0:4cff:febc:c5ba/64 Scope:Link
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:181237 errors:0 dropped:266 overruns:0 frame:0
          TX packets:43483 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:132347524 (126.2 MiB)TX bytes:4376937 (4.1 MiB)
          Interrupt:20 Base address:0xa000

lo      Link encap:Local Loopback
          inet addr:127.0.0.1Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNINGMTU:16436Metric:1
          RX packets:4148 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4148 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:3427368 (3.2 MiB)TX bytes:3427368 (3.2 MiB)

tap0      Link encap:EthernetHWaddr 00:FF:23:76:EB:D4
          inet addr:10.0.0.1Bcast:10.255.255.255Mask:255.0.0.0
          inet6 addr: fe80::2ff:23ff:fe76:ebd4/64 Scope:Link
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:500
          RX bytes:0 (0.0 b)TX bytes:90 (90.0 b)

virbr0    Link encap:EthernetHWaddr 00:00:00:00:00:00
          inet addr:192.168.122.1Bcast:192.168.122.255Mask:255.255.255.0
          inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)TX bytes:5045 (4.9 KiB)

# route
Kernel IP routing table
Destination    Gateway      Genmask      Flags Metric Ref    Use Iface
192.168.122.0*            255.255.255.0U    0      0      0 virbr0
192.168.111.0*            255.255.255.0U    0      0      0 eth0
link-local      *                255.255.0.0    U    0      0      0 eth0
10.0.0.0      *                255.0.0.0      U    0      0      0 tap0
default      192.168.111.10.0.0.0      UG    0      0      0 eth0
# ping 10.0.0.2 -c 3
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
From 10.0.0.1 icmp_seq=1 Destination Host Unreachable
From 10.0.0.1 icmp_seq=2 Destination Host Unreachable
From 10.0.0.1 icmp_seq=3 Destination Host Unreachable

--- 10.0.0.2 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2000ms
, pipe 3
#



谁能帮忙给看看,谢谢!急!

blue88128 发表于 2009-5-26 19:25:22

#skyeye config file sample
cpu: arm7tdmi

mach: at91

mem_bank: map=M, type=RW, addr=0x00000000, size=0x00004000
mem_bank: map=M, type=RW, addr=0x01000000, size=0x00400000
mem_bank: map=M, type=R,addr=0x01400000, size=0x00400000, file=./images/boot.rom
mem_bank: map=M, type=RW, addr=0x02000000, size=0x00400000
mem_bank: map=M, type=RW, addr=0x02400000, size=0x00008000
mem_bank: map=M, type=RW, addr=0x04000000, size=0x00400000
mem_bank: map=I, type=RW, addr=0xf0000000, size=0x10000000
#set nic info
#net: type=rtl8019, base=0xfffa0000, size=0x20,int=16, mac=0:4:3:2:1:f, ethmod=tuntap, hostip=10.0.0.1
net: type=rtl8019, ethmod=tuntap, hostip=10.0.0.1,state=on
#dbct: state=on
页: [1]
查看完整版本: 谁能帮忙给看看,谢谢!急!