# skyeye -c u-boot.conf
**************************** WARNING **********************************
If you want to run ELF image, you should use -e option to indicate
your elf-format image filename. Or you only want to run binary image,
you need to set the filename of the image and its entry in skyeye.conf.
***********************************************************************
big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x808131c
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
nandflash: dump ./nand.dump
file size:69206016
dbct info: turn on dbct!
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./u-boot.bin
Loaded RAM ./initrd.img
dbct translate block use memory 0x03ffff03 bytes.
ERROR: s3c2410x_io_write_word(0x4c000000) = 0x00ffffff
ERROR: s3c2410x_io_write_word(0x4c00000 = 0x00048032
U-Boot 1.1.4 (Mar 23 2008 - 18:47:45)
U-Boot code: 33F80000 -> 33F9BF0CBSS: -> 33F9FFE4
RAM Configuration:
Bank #0: 30000000 64 MB
Flash: 512 kB
NAND:64 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
SMDK2410 # tftp 0x33000000 uImage
TFTP from server 10.0.0.1; our IP address is 10.0.0.110
Filename 'uImage'.
Load address: 0x33000000
Loading: #################################################################
#################################################################
#################################################################
####
done
Bytes transferred = 1015092 (f7d34 hex)
SMDK2410 # nand erase 30000 F8000
NAND erase: device 0 offset 196608, size 1015808 ... OK
SMDK2410 # nand write 33000000 30000 f7d34
NAND write: device 0 offset 196608, size 1015092 ...1015092 bytes written: OK
SMDK2410 # # skyeye -c u-boot.conf
**************************** WARNING **********************************
If you want to run ELF image, you should use -e option to indicate
your elf-format image filename. Or you only want to run binary image,
you need to set the filename of the image and its entry in skyeye.conf.
***********************************************************************
big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x808131c
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
nandflash: dump ./nand.dump
file size:69206016
dbct info: turn on dbct!
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./u-boot.bin
Loaded RAM ./initrd.img
dbct translate block use memory 0x03ffff03 bytes.
ERROR: s3c2410x_io_write_word(0x4c000000) = 0x00ffffff
ERROR: s3c2410x_io_write_word(0x4c00000 = 0x00048032
U-Boot 1.1.4 (Mar 23 2008 - 18:47:45)
U-Boot code: 33F80000 -> 33F9BF0CBSS: -> 33F9FFE4
RAM Configuration:
Bank #0: 30000000 64 MB
Flash: 512 kB
NAND:64 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
SMDK2410 # nand read 33000000 30000 f7d34
NAND read: device 0 offset 196608, size 1015092 ...1015092 bytes read: OK
SMDK2410 # bootm
## Booting image at 33000000 ...
Image Name: Linux-2.6.14
Created: 2008-04-1213:42:43 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1015028 Bytes = 991.2 kB
Load Address: 30008000
Entry Point:30008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.................................................................... done, booting the kernel.
Linux version 2.6.14 ([email protected]) (gcc version 3.4.1) #6 Sat Apr 12 21:42:34 CST 2008
CPU: ARM920Tid(wb) revision 0 (ARMvundefined/unknown)
Machine: SMDK2410
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410 (id 0x32410000)
S3C2410: core 202.800 MHz, memory 101.400 MHz, peripheral 50.700 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: noinitrd console=ttySAC0 root=/dev/mtdblock2 rootfstype=yaffs init=/linuxrc devfs=mount ramdisk_size=2048 rw
irq: clearing pending status 00004000
irq: clearing pending status 00008000
irq: clearing pending status 00800000
irq: clearing pending status 10000000
irq: clearing subpending status 00000093
PID hash table entries: 128 (order: 7, 2048 bytes)
timer tcon=00500000, tcnt a509, tcfg 00000200,00000000, usec 00001e4c
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 16MB = 16MB total
Memory: 13996KB available (1689K code, 379K data, 96K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
softlockup thread 0 started up.
NET: Registered protocol family 16
S3C2410: Initialising architecture
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c1800000, irq 33
DMA channel 1 at c1800040, irq 34
DMA channel 2 at c1800080, irq 35
DMA channel 3 at c18000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x1
Console: switching to colour frame buffer device 80x25
fb0: Virtual frame buffer device, using 1024K of video memory
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 2048K size 1024 blocksize
loop: loaded (max 8 devices)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
eth0: CS8900A rev D at 0xe0000300 irq=53, no eeprom , addr: 08: 0:3E:26:0A:5B
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c1980000
s3c2410-nand: timing: Tacls 10ns, Twrph0 30ns, Twrph1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00100000 : "bootloader"
0x00100000-0x00400000 : "kernel"
0x00400000-0x02c00000 : "root"
0x02d00000-0x03c00000 : "user"
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
#
续问。。。
Default kernel command string为：noinitrd console=ttySAC0 root=/dev/mtdblock2 rootfstype=yaffs init=/linuxrc devfs=mount ramdisk_size=2048 rw
u-boot.conf内容为：
# skyeye config file for S3C2410X
cpu: arm920t
mach: s3c2410x
# physical memory
mem_bank: map=M, type=RW, addr=0x00000000, size=0x00800000, file=./u-boot.bin ,boot=yes
mem_bank: map=M, type=RW, addr=0xc0800000, size=0x00800000, file=./initrd.img----地址不是很确定
mem_bank: map=M, type=RW, addr=0x30000000, size=0x00800000
mem_bank: map=M, type=RW, addr=0x30800000, size=0x00800000
mem_bank: map=M, type=RW, addr=0x31000000, size=0x03000000
# all peripherals I/O mapping area
mem_bank: map=I, type=RW, addr=0x48000000, size=0x20000000
mem_bank: map=I, type=RW, addr=0x19000300, size=0x00000020
net: type=cs8900a, base=0x19000300, size=0x20,int=9, mac=0:4:3:2:1:f, ethmod=tuntap, hostip=10.0.0.1
nandflash: type=s3c2410x,name=K9F1208U0B,dump=./nand.dump
#lcd:type=s3c2410x, mod=gtk
dbct:state=on
~
# vi /usr/src/kernels/linux-2.6.14/arch/arm/mach-s3c2410/devs.c
/*1.建立Nand Flash分区表*/
/* 一个Nand Flash总共64MB, 按如下大小进行分区 */
/*
name: 代表分区名字
size: 代表flash分区大小(单位：字节)
offset: 代表flash分区的起始地址(相对于0x0的偏移)
*/
static struct mtd_partition partition_info[] = {
{ /* 1MB */
name: "bootloader",
size: 0x00100000,
offset: 0x0,
},
{ /* 3MB */
name: "kernel",
size: 0x00300000,
offset: 0x00100000,
},
{ /* 40MB */
name: "root",
size: 0x02800000,
offset: 0x00400000,
},
{ /* 20MB */
name: "user",
size: 0x00f00000,
offset: 0x02d00000,
}
};
内核配置是按照LZ的“http://blog.csdn.net/zblue78/archive/2008/02/20/2109827.aspx”中配置的
恳请大侠帮忙啊！！！
Default kernel command string
noinitrd console=ttySAC0 root=/dev/mtdblock2 init=/linuxrc ramdisk_size=2048 rw这个试过了吗？
回复 #18 crook 的帖子
NET: Registered protocol family 1Reading data from NAND FLASH without ECC is not recommended
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2) 这样的文章很稀有
珍惜啊
我怎么作不出来啊 我的那里出了问题呢？
先赞一个我按lz说的方法去作了，可是在没有添加nand部分时执行的还好，即第7步之前正常。
但做到第10步的时候就不行了呢，
结果是
:~/arm/rom3$ ls
nand.dumpskyeye.confskyeye.conf~u-bootu-boot.bin
:~/arm/rom3$ sudo skyeye
**************************** WARNING **********************************
If you want to run ELF image, you should use -e option to indicate
your elf-format image filename. Or you only want to run binary image,
you need to set the filename of the image and its entry in skyeye.conf.
***********************************************************************
big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x805f420
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
failed to setup_module (name:net, type:cs8900a)
nandflash: dump ./nand.dump
tapif_init: icotl TUNSETIFF errorfile size:69206016
dbct info: Note: DBCT not compiled in. This option will be ignored
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./u-boot.bin
到这里就进行不下去了。这是为什么阿 ，其他的和你做的一样，SKYEYE。CONF也是一样的。
这样执行也不行
shinety@shinety:~/arm/rom3$ sudo skyeye
**************************** WARNING **********************************
If you want to run ELF image, you should use -e option to indicate
your elf-format image filename. Or you only want to run binary image,
you need to set the filename of the image and its entry in skyeye.conf.
***********************************************************************
big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x805f420
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
failed to setup_module (name:net, type:cs8900a)
nandflash: dump ./nand.dump
tapif_init: icotl TUNSETIFF errorfile size:69206016
dbct info: Note: DBCT not compiled in. This option will be ignored
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./u-boot.bin
+Stopped sudo skyeye
shinety@shinety:~/arm/rom3$ sudo skyeye -e u-boot
big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x805f420
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
failed to setup_module (name:net, type:cs8900a)
nandflash: dump ./nand.dump
tapif_init: icotl TUNSETIFF errorfile size:69206016
dbct info: Note: DBCT not compiled in. This option will be ignored
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./u-boot.bin
start addr is set to 0x33f80000 by exec file.
SKYEYE:NumInstrs 26021, mem_write_byte addr = 3400006d no bank
我在想是不是地址有问题。lz觉得我这边有什么不对的阿？
[ 本帖最后由 shinety53 于 2008-4-30 21:41 编辑 ] r看看,做实验,发现很多问题! 原帖由 shinety53 于 2008-4-30 21:18 发表 http://www.linuxfans.org/bbs/images/common/back.gif
先赞一个
我按lz说的方法去作了，可是在没有添加nand部分时执行的还好，即第7步之前正常。
但做到第10步的时候就不行了呢，
结果是
:~/arm/rom3$ ls
nand.dumpskyeye.confskyeye.conf~u-bootu-b ...
用skyeye 提供的mknandflashdump程序将 我们的u-boot.bin文件镜像到nand.dump 文件中
mknandflashdump u-boot.bin nand.dump 0
没有做这个? 请问楼主是怎么用skyeye就跟踪代码的。给个详细点步骤好吗？谢谢！！ lz的conf如下，有几点不懂想请教：
# physical memory
mem_bank: map=M, type=RW, addr=0x00000000, size=0x00800000,
file=./u-boot.bin ,boot=yes
请问这里指定的是nand flash吗?
如果是nor flash，怎么指定是从nand flash启动的呢？
如果是nand flash的话，2410中nand flash实际上不是连接到memory bank上的，为什么要这样指定？
我想仿照您的方法在skyeye for 2410中启动vivi，但是没有成功，故有以上疑惑。望指教，谢谢！ 想s3c2410这样的芯片之所以可以在NAND上启动，是由于s3c2410有一个叫做stepping stone的内置SRAM，将loader代码烧在NAND上，加电后，该芯片可以自动将NAND的起始4k的内容拷贝到SRAM里，然后在RAM里执行。 修改 command/cmd_nand.c
中的NanD_ReadBuf函数
注释掉NanD_Command (nand, NAND_CMD_READ0);这一行
俺的是u-boot1.2.0竟然没有这个函数，自己弄了好久，不知该怎么改。
页:
1
[2]