gentoo下用adsl-setup的問題
我裝上了adsl-setup以後, 執行adsl-start, 能執行成功但是還是不能上網. 求助各位eth0 Link encap:EthernetHWaddr 00:05:5D:29:16:4B
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b)TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1Mask:255.0.0.0
UP LOOPBACK RUNNINGMTU:16436Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b)TX bytes:0 (0.0 b)
#***********************************************************************
#
# pppoe.conf
#
# Configuration file for rp-pppoe.Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the adsl-start, adsl-stop, adsl-connect and
# adsl-status shell scripts.It is *not* used in any way by the
# "pppoe" executable.
#
# Copyright (C) 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# LIC: GPL
# $Id: pppoe.conf,v 1.10 2002/04/09 17:28:38 dfs Exp $
#***********************************************************************
# When you configure a variable, DO NOT leave spaces around the "=" sign.
# Ethernet card connected to ADSL modem
#
# NB: Gentoo overrides ETH when adsl-start is called from the
# networking scripts.This setting has no effect in that case.
ETH='eth0'
# ADSL user name.You may have to supply "@provider.com"Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication.Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use [email protected]
USER='110110110'
# Bring link up on demand?Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300
# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=NOCHANGE
# Obtain DNS server addresses from the peer (recent versions of pppd only)
# In old config files, this used to be called USEPEERDNS.Changed to
# PEERDNS for better Red Hat compatibility
PEERDNS=no
DNS1=
DNS2=
# Make the PPPoE connection your default route.Set to
# DEFAULTROUTE=no if you don't want this.
DEFAULTROUTE=yes
### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT
# How long adsl-start waits for a new PPP interface to appear before
# concluding something went wrong.If you use 0, then adsl-start
# exits immediately with a successful status and does not wait for the
# link to come up.Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0.This makes SURE that the machine keeps trying
# to connect forever after adsl-start is called.Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30
# How often in seconds adsl-start polls to check if link is up
CONNECT_POLL=2
# Specific desired AC Name
ACNAME=
# Specific desired service name
SERVICENAME=
# Character to echo at each poll.Use PING="" if you don't want
# anything echoed
PING="."
# File where the adsl-connect script writes its process-ID.
# Three files are actually used:
# $PIDFILE contains PID of adsl-connect script
# $PIDFILE.pppoe contains PID of pppoe process
# $PIDFILE.pppdcontains PID of pppd process
#
# NB: Gentoo overrides PIDFILE when adsl-start is run from the
# networking scripts.This setting has no effect in that case.
PIDFILE="/var/run/$CF_BASE-adsl.pid"
# Do you want to use synchronous PPP?"yes" or "no"."yes" is much
# easier on CPU usage, but may not work for you.It is safer to use
# "no", but you may want to experiment with "yes"."yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no
# Do you want to clamp the MSS?Here's how to decide:
# - If you have only a SINGLE computer connected to the ADSL modem, choose
# "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
# The setting of 1412 is safe for either setup, but uses slightly more
# CPU power.
CLAMPMSS=1412
#CLAMPMSS=no
# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3
# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80
# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=NONE
# Linux kernel-mode plugin for pppd.If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=
# Any extra arguments to pass to pppoe.Normally, use a blank string
# like this:
PPPOE_EXTRA=""
# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect ADSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"
# Any extra arguments to pass to pppd.Normally, use a blank string
# like this:
PPPD_EXTRA=""
########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING
# If you wish to COMPLETELY overrride the pppd invocation:
# Example:
# OVERRIDE_PPPD_COMMAND="pppd call dsl"
# If you want adsl-connect to exit when connection drops:
# RETRY_ON_FAILURE=no 我用的是cnc的adsl DNS 用 server 试试
另外不要打开net.eth0 把它从default runlever 中去掉 一般是路由的事吧，你到精华贴里找找吧
如果用能ip上网站，那就是DNS的问题 reslov.conf :arrow:
页:
[1]