redhat 9.0增加一个200G的硬盘fdisk不认
redhat 9.0操作系统,原来安装一块80G硬盘HDA,工作正常.准备新加一块WD 200G IDE硬盘.bios正常,dmesg正常,fdisk /dev/hda正常, fdisk /dev/hdc报错Unable to open /dev/hdc
无计可施了....各位DX救命啊!
dmesg如下:
Linux version 2.4.20-8 ([email protected]) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Mar 13 17:54:28 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable)
BIOS-e820: 000000003f7f0000 - 000000003f7f3000 (ACPI NVS)
BIOS-e820: 000000003f7f3000 - 000000003f800000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 260080
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 30704 pages.
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1799.980 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3591.37 BogoMIPS
Memory: 1019400k/1040320k available (1347k kernel code, 17400k reserved, 999k data, 132k init, 122816k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 1.80GHz stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfba10, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX at 00:1f.0
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 00:1d.2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 00:1d.2
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
hda: HDS728080PLAT20, ATA DISK drive
blk: queue c03c9f40, I/O limit 4095Mb (mask 0xffffffff)
hdc: WDC WD2000JB-22GVC0, ATA DISK drive
blk: queue c03ca3a0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=10011/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 143k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting.Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 9 for device 00:1d.7
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller
ehci-hcd 00:1d.7: irq 9, pci mem f8849000
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:1d.0
PCI: Sharing IRQ 5 with 00:02.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:1d.1
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:1d.2
PCI: Sharing IRQ 11 with 00:1f.1
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 2104472k swap-space (priority -1)
kjournald starting.Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices fdisk好象不支持那么大的硬盘啊 hda: host protected area => 1
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=10011/255/63, UDMA(100)
我看到这一部分参数，hda参数正确识别了，但是hdc参数没有。查kudzu，也是hda正确识别，hdc参数没有。手工加参数，调用fdisk，还是不灵。
实在不行，明天我装as3了。亲戚朋友都在用as3，好像大硬盘没有问题。 问题应该在fdisk上啊，RH9好象也是最多支持130G的盘 我有个160G的硬盘，用fdisk没有问题。不过我的系统是gentoo。
页:
[1]