itsenser 发表于 2005-10-17 11:03:46

CDMA无线上网卡的痛苦安装过程--至今没有成功,都来看一下

我用的是IBM ThinkPad T40,系统安装的是suse 10,无线上网卡是三目通的2188C
suse 10安装完成后没有认出CDMA,后安装pcmcia3.2.8后无线上网卡认出为serial or modem,插入卡时
也会beep了,但/var/log/messages中显示的信息为:

Oct 17 10:37:34 linux cardmgr: socket 1: CDMA CARD
Oct 17 10:37:34 linux cardmgr: get dev info on socket 1 failed: No such device
Oct 17 10:37:34 linux kernel: 1.0: RequestIO: No more items

用cardctl ident的输出如下:
linux:/home/itsenser # cardctl ident
Socket 0:
no product info available
Socket 1:
product info: "CDMA CARD", "2188C", "", ""
manfid: 0x0279, 0x950b
function: 2 (serial)

用cardctl config的输出如下:
linux:/home/itsenser # cardctl config
Socket 0:
not configured
Socket 1:
Vcc 5.0V Vpp1 5.0V Vpp2 5.0V

用cardctl info的输出如下:
linux:/home/itsenser # cardctl info
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
PRODID_1="CDMA CARD"
PRODID_2="2188C"
PRODID_3=""
PRODID_4=""
MANFID=0279,950b
FUNCID=2

用lspci -vv 信息好下只保留连了相关部分)
02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: IBM ThinkPad T30/T40
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: e8000000-e9fff000 (prefetchable)
Memory window 1: c2000000-c3fff000
I/O window 0: 00004000-00004fff
I/O window 1: 00005000-00005fff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001

02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: IBM ThinkPad T30/T40
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin B routed to IRQ 5
Region 0: Memory at b1000000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: ea000000-ebfff000 (prefetchable)
Memory window 1: c4000000-c5fff000
I/O window 0: 00006000-00006fff
I/O window 1: 00007000-00007fff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001

itsenser 发表于 2005-10-17 11:04:27

用dmesg信息如下:
Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002ff60000 (usable)
BIOS-e820: 000000002ff60000 - 000000002ff77000 (ACPI data)
BIOS-e820: 000000002ff77000 - 000000002ff79000 (ACPI NVS)
BIOS-e820: 000000002ff80000 - 0000000030000000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
767MB LOWMEM available.
On node 0 totalpages: 196448
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192352 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v002 IBM ) @ 0x000f6d70
ACPI: XSDT (v001 IBM TP-1R 0x00003180 LTP 0x00000000) @ 0x2ff6a6cd
ACPI: FADT (v003 IBM TP-1R 0x00003180 IBM 0x00000001) @ 0x2ff6a800
ACPI: SSDT (v001 IBM TP-1R 0x00003180 MSFT 0x0100000e) @ 0x2ff6a9b4
ACPI: ECDT (v001 IBM TP-1R 0x00003180 IBM 0x00000001) @ 0x2ff76ebc
ACPI: TCPA (v001 IBM TP-1R 0x00003180 PTL 0x00000001) @ 0x2ff76f0e
ACPI: BOOT (v001 IBM TP-1R 0x00003180 LTP 0x00000001) @ 0x2ff76fd8
ACPI: DSDT (v001 IBM TP-1R 0x00003180 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: local apic disabled
Allocating PCI resources starting at 30000000 (gap: 30000000:cf800000)
Built 1 zonelists
Kernel command line: root=/dev/hda5 vga=791 selinux=0 devfs=nomount,all resume=/dev/hda6 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1495.418 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 773200k/785792k available (2028k kernel code, 12068k reserved, 700k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2993.09 BogoMIPS (lpj=5986198)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) M processor 1500MHz stepping 05
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1719k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0820)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link (IRQs 3 4 *5 6 7 9 10 11)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller (gpe 28)
ACPI: Power Resource (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
request_module: runaway loop modprobe char-major-1-11
request_module: runaway loop modprobe char-major-1-11
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to [email protected] cc [email protected])
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: c0100000-c01fffff
PREFETCH window: e0000000-e7ffffff
PCI: Bus 3, cardbus bridge: 0000:02:00.0
IO window: 00004000-00004fff
IO window: 00005000-00005fff
PREFETCH window: e8000000-e9ffffff
MEM window: c2000000-c3ffffff
PCI: Bus 7, cardbus bridge: 0000:02:00.1
IO window: 00006000-00006fff
IO window: 00007000-00007fff
PREFETCH window: ea000000-ebffffff
MEM window: c4000000-c5ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 4000-8fff
MEM window: c0200000-cfffffff
PREFETCH window: e8000000-efffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:00.0 -> Link -> GSI 11 (level, low) -> IRQ 11
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:00.1 -> Link -> GSI 5 (level, low) -> IRQ 5
Simple Boot Flag at 0x35 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1129545251.264:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xe0000000, mapped to 0xf0880000, using 6144k, total 32704k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:5710
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 bytes,<6>...found (1024x768, 12703 bytes, v3).
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
pnp: Device 00:08 activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:1f.6 -> Link -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
LID SLPB PCI0 UART PCI1 USB0 USB1 AC9M
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1 -> Link -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdcMA, hddio
Probing IDE interface ide0...
hda: HITACHI_DK23EB-40B, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 > hda3
Probing IDE interface ide1...
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
hdc: UJDA745 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1 C2 C3)
ACPI: Processor (supports 8 throttling states)
ACPI: Thermal Zone (51 C)
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
input: PS/2 Generic Mouse on synaptics-pt/serio0
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
bootsplash: status on console 0 changed to off
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
pnp: Device 00:09 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x3bc, irq 7
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
thinkpad: module not supported by Novell, setting U taint flag.
thinkpad: I have registered to handle major: 10 minor: 170.
Adding 1005440k swap on /dev/hda6. Priority:-1 extents:1
Non-volatile memory driver v1.2
lp0: using parport0 (interrupt-driven).
hw_random: RNG not detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
shpchp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
shpchp: acpi_shpchprm: Slot sun(1) at s:b:d:f=0x00:02:00:00
shpchp: acpi_shpchprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
shpchp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
shpchp: acpi_shpchprm: Slot sun(2) at s:b:d:f=0x00:02:00:01
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0 -> Link -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1 -> Link -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
shpchp: shpc_init : shpc_cap_offset == 0
ACPI: PCI Interrupt 0000:00:1d.2 -> Link -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usb 2-2: new low speed USB device using uhci_hcd and address 2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: PCI Interrupt Link enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7 -> Link -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-2: USB disconnect, address 2
usb 2-2: new low speed USB device using uhci_hcd and address 3
ACPI: PCI Interrupt 0000:00:1f.5 -> Link -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
usbcore: registered new driver hiddev
Intel(R) PRO/1000 Network Driver - version 6.0.60-k2-NAPI
Copyright (c) 1999-2005 Intel Corporation.
input: USB HID v1.10 Mouse on usb-0000:00:1d.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
intel8x0_measure_ac97_clock: measured 55402 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:02:01.0 -> Link -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:02:00.0 -> Link -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:00.0
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Yenta: ISA IRQ mask 0x0458, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
cs: IO port probe 0x4000-0x8fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
ACPI: PCI Interrupt 0000:02:00.1 -> Link -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:02:00.1
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64
Yenta: ISA IRQ mask 0x0008, PCI irq 5
Socket status: 30000011
pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff
cs: IO port probe 0x4000-0x8fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
cs: memory probe 0xe8000000-0xefffffff: excluding 0xe8000000-0xefffffff
cs: memory probe 0xc0200000-0xcfffffff: excluding 0xc0200000-0xc11fffff 0xc1a00000-0xc61fffff 0xc6a00000-0xc71fffff 0xc7a00000-0xc81fffff 0xc8a00000-0xc91fffff 0xc9a00000-0xca1fffff 0xcaa00000-0xcb1fffff 0xcba00000-0xcc1fffff 0xcca00000-0xcd1fffff 0xcda00000-0xce1fffff 0xcea00000-0xcf1fffff 0xcfa00000-0xd01fffff
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
1.0: RequestIO: No more items
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
ACPI: AC Adapter (on-line)
IA-32 Microcode Update Driver: v1.14 <[email protected]>
microcode: CPU0 not 'upgrading' to earlier revision 0x5 (current=0x7)
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
ACPI: Battery Slot (battery present)
ACPI: Power Button (FF)
ACPI: Lid Switch
ACPI: Sleep Button (CM)
ibm_acpi: IBM ThinkPad ACPI Extras v0.11
ibm_acpi: http://ibm-acpi.sf.net/
ACPI-0077: *** Warning: No context for object
ibm_acpi: dock device not present
mtrr: 0xe0000000,0x2000000 overlaps existing 0xe0000000,0x1000000
Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt 0000:01:00.0 -> Link -> GSI 11 (level, low) -> IRQ 11
Initialized radeon 1.16.0 20050311 on minor 0:
mtrr: 0xe0000000,0x2000000 overlaps existing 0xe0000000,0x1000000
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
1.0: RequestIO: No more items

itsenser 发表于 2005-10-17 11:04:50

我在config中加入了以下内容:
card "CDMA CARD"
manfid 0x0279, 0x950b
bind "serial_cs"


在config.opts中加入了以下内容:

#for cdma
include port 0x4000-0x7fff
include memory 0xc2000000-0xebfff000

youngbamboo 发表于 2005-10-17 19:47:10

我忙活了好久,也实现不了

xixixixi 发表于 2005-10-20 15:05:48

等你安装好了我也装装.

HeartIcy 发表于 2005-10-21 18:27:34

http://www.szcdma.com/bbs/showbbs.asp?bd=2&id=15&totable=1

me too,我从讯畅发了贴子,可是也没用。

to itsenser

你的这些东西是根据那里的信息来定的?
manfid 0x0279, 0x950b

itsenser 发表于 2005-10-24 17:29:03

根据设备的实际信息就是厂商、产品号之类的东东
用cardctl ident就可以得到

linky_fan 发表于 2005-10-26 15:25:35

http://www.linuxfans.org/nuke//modules.php?name=Forums&file=viewtopic&t=119392&highlight=cdma

其实我觉得cdma上网还是用手机+数据线方便些.
页: [1]
查看完整版本: CDMA无线上网卡的痛苦安装过程--至今没有成功,都来看一下