cHensIr 发表于 2005-11-4 13:24:07

请教skyeye 1.0下仿真EP9312

新手请教：
我自己新编译的内核为2.4.8.1，用的是arm.cirrus.com上提供的cirrus-linux-1.04.patch的针对cirrus logic的内核补丁。
交叉编译环境为自己编译的工具链：
binutils-2.15
gcc-2.4.4
glibc-2.2.5
glibc-linuxthreads-2.2.5
工具链是根据http://kegel.com/crosstool/上提供的crosstool-0.38的脚本编译的。
工具链编译很正常，而且，用编译好的工具链编译我自己的内核也能编译成功，我想验证一下我的内核和工具链是不是工作正常，所以，把我内核产生的vmlinux弄到skyeye 1.0里边验证一下。
但是现在出现了一个问题，我的2.6.8.1内核在skyeye 1.0里边运行不正常，跑一段之后就挂掉了。

在skyeye的skyeye.conf文件是testsuite 2.0里边的ep9312的skyeye.conf

################skyeye.conf#################
cpu: arm920t
mach: ep9312

#mem_bank: map=F, type=R,addr=0x10000000, size=0x00080000, file=./redboot.bin,boot=yes
mem_bank: map=I, type=RW, addr=0x80000000, size=0x000d0000
mem_bank: map=I, type=RW, addr=0x80800000, size=0x00150000
mem_bank: map=I, type=RW, addr=0x80950000, size=0x00000008   
mem_bank: map=M, type=RW, addr=0xC0000000, size=0x01000000
mem_bank: map=M, type=RW, addr=0xC1000000, size=0x01000000,file=./initrd.img
#log: logon=1, logfile=/tmp/test.log, start=0x100000, end=0x100100
#dbct:state=on

#lcd: state=on

#net: state=on, mac=0:4:3:2:1:f, #ethmod=tuntap,hostip=192.168.1.235

用skyeye -c skyeye.conf -e vmlinux 开始测试我的内核
输出信息如下：

------------------------- SkyEye -V1.0 ---------------------------
Usage: SkyEye program
Default mode is STANDALONE mode
------------------------------------------------------------------
Options:
-e exec-file      the (ELF executable format)kernel file name.
-d                  in GDB Server mode (can be connected by GDB).
-c config-file      the skyeye configure file name.
-h                  This Help Display
------------------------------------------------------------------
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name ep9312, mach_init addr 0x8093044
SKYEYE: use arm920t mmu ops
Linux version 2.6.8.1 ([email protected]) (gcc version 3.4.4) #18 Fri Nov 4 12:05:13 CST 2005
CPU: ARM920Tid(wb) revision 0 (ARMvundefined/unknown)
CPU: D VIVT write-back cache
CPU: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: edb9312
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: root=/dev/ram initrd=0xC1000000,0x200000 rw console=ttyAM0 mem=32M
PID hash table entries: 256 (order 8: 2048 bytes
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 27728KB available (1930K code, 575K data, 84K init)
Calibrating delay loop... 25.80 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2048K
NET: Registered protocol family 16


我的内核运行到这里就不跑下去了，我也查了很久没查到是什么问题。
但是，应该肯定的是，内核的前边一部份是跑起来了，但是为什么不接着跑下去，这个我就搞不清楚了。

哪位仁兄弄过9312板子的，给点建议好不？
或者是能把你的工具链和内核版本和补丁包报一下。。。。。
小弟不胜感激！！

ksh 发表于 2005-11-4 13:52:53

I guess probably thereneed to get rid of some options in make menuconfig. For some hardware is not simulated by SkyEye. Maybe you can get rid of network option and try again?

cHensIr 发表于 2005-11-4 14:26:18

我把网络取消掉了，还是一样的问题。
Linux NoNET1.0 for Linux 2.6

接着也是没有了下一步了。

我看了一下testsuite 2.0下提供的EP9312映像的启动信息，应该是下边这样的。


Linux version 2.6.12 (skyeyeuser@debian) (gcc version 3.3.2) #2 Fri Aug 5 14:03:55 CST 2005
CPU: ARM920Tid(wb) revision 0 (ARMvundefined/unknown)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: edb9312
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: root=/dev/ram initrd=0xC1000000,0x200000 console=ttyAM0 rw
PID hash table entries: 256 (order: 8, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 29056KB available (852K code, 312K data, 72K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2048K
Linux NoNET1.0 for Linux 2.6
CPU model: Cirrus Logic EP9315, silicon rev A
NetWinder Floating Point Emulator V0.97 (double precision)
Serial: EP93xx driver $Revision: 1.42 $
ttyAM0 at MMIO 0x808c0000 (irq = 52) is a uart-ep93xx
ttyAM1 at MMIO 0x808d0000 (irq = 54) is a uart-ep93xx
ttyAM2 at MMIO 0x808e0000 (irq = 55) is a uart-ep93xx
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
physmap flash device: 2000000 at 60000000
mice: PS/2 mouse device common for all mice
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 2048KiB into ram disk...

根它比较的情况来看，好像我的内核是在检测CPU model:的时候挂了。
是不是我的内核哪里没配置好？还是还有什么补丁没打上？
说明一下，我自己没有做文件系统映像，而是直接用的testsuite 2.0里边给的initrd.img，因为我想有没有这个映像不会影响到内核的启动；最多是在启动的最后报错，说不能init。
请教。。。。。

cHensIr 发表于 2005-11-4 14:49:28

我基本上把make menuconfig 里边的其他模块都给去掉了，但是好像结果一样哦。

------------------------- SkyEye -V1.0 ---------------------------
Usage: SkyEye program
Default mode is STANDALONE mode
------------------------------------------------------------------
Options:
-e exec-file      the (ELF executable format)kernel file name.
-d                  in GDB Server mode (can be connected by GDB).
-c config-file      the skyeye configure file name.
-h                  This Help Display
------------------------------------------------------------------
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name ep9312, mach_init addr 0x8093044
SKYEYE: use arm920t mmu ops
Linux version 2.6.8.1 ([email protected]) (gcc version 3.4.4) #19 Fri Nov 4 14:35:15 CST 2005
CPU: ARM920Tid(wb) revision 0 (ARMvundefined/unknown)
CPU: D VIVT write-back cache
CPU: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: edb9312
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: root=/dev/ram initrd=0xC1000000,0x200000 rw console=ttyAM0 mem=32M
PID hash table entries: 256 (order 8: 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 28688KB available (1190K code, 377K data, 60K init)
Calibrating delay loop... 25.80 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2048K
Linux NoNET1.0 for Linux 2.6



我的内核的.config文件：
#
# Automatically generated make config: don't edit
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y

#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y

#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODULE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_KMOD is not set

#
# System Type
#
# CONFIG_ARCH_CLPS7500 is not set
CONFIG_ARCH_EP93XX=y
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_CAMELOT is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_IOP3XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_VERSATILE_PB is not set

#
# Cirrus Logic EP93xx options
#
# CONFIG_ARCH_EDB9301 is not set
# CONFIG_ARCH_EDB9302 is not set
# CONFIG_ARCH_EDB9307 is not set
CONFIG_ARCH_EDB9312=y
# CONFIG_ARCH_EDB9315 is not set
# CONFIG_ARCH_EDB9315A is not set
CONFIG_EP93XX_CS0=y
# CONFIG_EP93XX_CS1 is not set
# CONFIG_EP93XX_CS2 is not set
# CONFIG_EP93XX_CS3 is not set
# CONFIG_EP93XX_CS6 is not set
# CONFIG_EP93XX_CS7 is not set
CONFIG_EP93XX_SDCS0=y
# CONFIG_EP93XX_SDCS1 is not set
# CONFIG_EP93XX_SDCS2 is not set
# CONFIG_EP93XX_SDCS3 is not set
CONFIG_EP93XX_SYNC_BOOT=y
# CONFIG_EP93XX_FPU is not set
CONFIG_ARCH_EP9312=y
CONFIG_EP93XX_FRAMEBUFFER=y
CONFIG_EP93XX_FLASH_BASE=0xf0000000
CONFIG_EP93XX_FLASH_SIZE=0x02000000
CONFIG_EP93XX_FLASH_WIDTH=4
CONFIG_EP93XX_PHYS_ADDR=0xc0000000
CONFIG_EP93XX_ZREL_ADDR=0xc0008000
CONFIG_EP93XX_PARAMS_PHYS=0xc0000100
CONFIG_EP93XX_INITRD_PHYS=0xc1000000

#
# Processor Type
#
CONFIG_CPU_32=y
CONFIG_CPU_ARM920T=y
CONFIG_CPU_32v4=y
CONFIG_CPU_ABRT_EV4T=y
CONFIG_CPU_CACHE_V4WT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y

#
# Processor Features
#
# CONFIG_ARM_THUMB is not set
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set

#
# General setup
#
# CONFIG_ZBOOT_ROM is not set
CONFIG_ZBOOT_ROM_TEXT=0
CONFIG_ZBOOT_ROM_BSS=0

#
# PCMCIA/CardBus support
#
CONFIG_PCMCIA=y
# CONFIG_PCMCIA_DEBUG is not set
# CONFIG_TCIC is not set
# CONFIG_PCMCIA_EP93XX is not set

#
# At least one math emulation must be selected
#
CONFIG_FPE_NWFPE=y
# CONFIG_FPE_NWFPE_XP is not set
# CONFIG_FPE_FASTFPE is not set
# CONFIG_VFP is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_PM is not set
# CONFIG_PREEMPT is not set
# CONFIG_ARTHUR is not set
CONFIG_CMDLINE="root=/dev/ram initrd=0xC1000000,0x200000 rw console=ttyAM0 mem=32M"
CONFIG_ALIGNMENT_TRAP=y

#
# Parallel port support
#
# CONFIG_PARPORT is not set

#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_REDBOOT_PARTS=y
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AFS_PARTS is not set

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=y
# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_OBSOLETE_CHIPS is not set

#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
CONFIG_MTD_EDB93XX=y

#
# Self-contained MTD device drivers
#
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLKMTD is not set

#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set

#
# NAND Flash Device Drivers
#
# CONFIG_MTD_NAND is not set

#
# Plug and Play support
#

#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Networking support
#
# CONFIG_NET is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set

#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set

#
# SCSI device support
#
# CONFIG_SCSI is not set

#
# Fusion MPT device support
#

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#

#
# ISDN subsystem
#

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
# CONFIG_SERIO_I8042 is not set
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set

#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_TOUCHSCREEN_EP93XX is not set
# CONFIG_INPUT_MISC is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_EP93XX=y
CONFIG_SERIAL_EP93XX_CONSOLE=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_QIC02_TAPE is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_RAW_DRIVER is not set

#
# I2C support
#
# CONFIG_I2C is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
CONFIG_JFS_FS=y
# CONFIG_JFS_POSIX_ACL is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
# CONFIG_MSDOS_FS is not set
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS_XATTR=y
# CONFIG_DEVPTS_FS_SECURITY is not set
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_JFFS_FS=y
CONFIG_JFFS_FS_VERBOSE=0
CONFIG_JFFS_PROC_FS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
# CONFIG_JFFS2_FS_NAND is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set

#
# Profiling support
#
# CONFIG_PROFILING is not set

#
# Graphics support
#
# CONFIG_FB is not set

#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y

#
# Sound
#
# CONFIG_SOUND is not set

#
# Misc devices
#

#
# USB support
#
# CONFIG_USB is not set

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# Kernel hacking
#
CONFIG_FRAME_POINTER=y
# CONFIG_DEBUG_USER is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_KERNEL is not set

#
# Security options
#
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
# CONFIG_CRYPTO is not set

#
# Library routines
#
# CONFIG_CRC_CCITT is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y


请高手指教指教。。。。。

sandahrow 发表于 2006-3-22 22:27:16

你的内核不支持ext3？也许问题出在这！

你的内核不支持ext3？也许问题出在这！

sandahrow 发表于 2006-3-22 22:32:30

我也问一下，怎么在qt上使用mouse,我的mouse运行不正常。
另外用2.6.8.1时，reboot或者reset又或者断电再上电的时候会不会出现启动不了？
页: [1]
查看完整版本: 请教skyeye 1.0下仿真EP9312