求助各位老大帮小弟解决个问题!(小弟是个菜鸟)
我买一个WD-100聪明型双串口多用户卡,因为我的电脑只有两个COM口,需要增加COM口就买了这个,但是不会用,主要是不会找驱动和编译!请各位大哥帮帮忙!我买的WD-100聪明型双串口多用户卡的网址:http://www.link-max.com/products/multi/wd100.htm
这是LINUX的使用说明(因为我刚接触LINUX不久,不会弄)
This installation guide describes the procedures to install NetMos Technology Nm9735CV, Nm9745CV, Nm9835CV, Nm9845CV PCI serial ports in Linux platform.
Linux Platform
l Operating System : RedHat, SuSe
l Terminal Emulation AP : minicom
l Internet Dialer : Kppp
Find the available serial ports
Since Linux only support 4 serial ports (ttyS0, ttyS1, ttyS2, ttyS3) under the default condition. Most likely, ttyS0 & ttyS1 are supported by mother board's built-in serial controllers and ttyS2 & ttyS3 are free for additional I/O card.
Serial ports could be checked by the following commands.
setserial /dev/ttyS0 -a (COM-1)
setserial /dev/ttyS1 -a (COM-2)
setserial /dev/ttyS2 -a (COM-3)
setserial /dev/ttyS3 -a (COM-4)
If COM-1 is used by mouse, the response is similar to
/dev/ttyS0 : Device or resource busy
If the COM-1 does not attach any device, the response is similar to
/dev/ttyS0, Line 0, UART: 16550A, Port: 0x3f8, irq: 4
Baud_base: 115200, clos_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinite
Flags: spd_normal skip_test
In case ttyS2 (COM-3) is free, the response for command setserial /dev/ttyS2 -a is shown below.
/dev/ttyS2, Line 2, UART: unknown, Port: 0x3e8, irq: 4
Baud_base: 115200, clos_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinite
Flags: spd_normal skip_test
Find the PCI card resource ( I/O port address & IRQ) for the serial ports
Enter the command more /proc/pci
The response is similar to the following
Bus 0, Device 11, function 0:
Serial controller : Unknown vendor Unknown device (rev 01).
Vendor id=9710, Device id=9735
Device id=9745
Device id=9820
Device id=9825
Device id=9835
Device id=9845
Medium devsel. Fast back-to-back capable. IRQ 11
Board with Nm9735CV part
I/O at 0xc000 serial port 1
0xc008 serial port 2
Board with Nm9745CV part
I/O at 0xc000 serial port 1
0xc008 serial port 2
0xc010 device 1
0xc018 device 2
0xc020 device 3
0xc028 device 4
Board with Nm9820CV part
I/O at 0xc000 serial port 1
I/O at 0xc400 not used
I/O at 0xc800 not used
I/O at 0xd000 not used
I/O at 0xd400 not used
I/O at 0xd800 not used
Board with Nm9825CV part
I/O at 0xc000 serial port 1
Board with Nm9835CV part
I/O at 0xc000 serial port 1
I/O at 0xc400 serial port 2
I/O at 0xc800 not used
I/O at 0xd000 not used
I/O at 0xd400 not used
I/O at 0xd800 not used
Board with Nm9845CV part
I/O at 0xc000 serial port 1
I/O at 0xc400 serial port 2
I/O at 0xc800 device 1
I/O at 0xd000 device 2
I/O at 0xd400 device 3
I/O at 0xd800 device 4
Board with Nm9755CV part
I/O at 0xc000 not used
I/O at 0xc400 not used
I/O at 0xc800 device 1
I/O at 0xd000 device 2
I/O at 0xd400 device 3
I/O at 0xd800 device 4
From the /proc/pci file, it is possible to find the PCI card's I/O port address and IRQ. Especially, the NetMos parts always shows
Vendor id=9710, Device id=9735
Device id=9745
Device id=9820
Device id=9825
Device id=9835
Device id=9845
Configure the parameters for ttyS2 or ttyS3
Enter (if ttyS2 or ttyS3 are free)
setserial /dev/ttyS2 port 0xc000 UART 16550A
irq 11 Baud_base 115200
setserial /dev/ttyS3 port 0xc008 UART 16550A
irq 11 Baud_base 115200
Check the setting for ttyS2 or ttyS3
Type setserial /dev/ttyS2 -a
/dev/ttyS2, Line 2, UART: 16550A, Port: 0xc000, irq: 11
Baud_base: 115200, clos_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinite
Flags: spd_normal skip_test
The ttyS2 or ttyS3 are ready for application
在此麻烦各位老大帮忙,谢谢! 各位大大们帮帮忙呀,急.....................
页:
[1]