安装SUSE10.2出现的问题
各位大大好:今天下完-386ISO . DVD,查完MD5,一切正常.刻盘,安装.问题来了:
我用光驱引导全新安装,引导正常,选语言为简体中文,在安装选项按回车.然后就是画面了.那个图标在那里一直转,一直转,转了N久,弹出了经色的框框,警告说:没找到安装盘-CD(当然是英文提示了,嘿嘿),点OK,进入下一个页面.里面有这些选项:设置.从硬盘安装,从光驱安装,从硬盘启动.,重启,关机..这些选项都是可以进入的,我点从光驱安装,提示说:光驱里没安装盘,我郁闷,明明在里面怎么会没有呢?
我重启了,引导到第一个画面.我选查看硬件的那个选项(在最下面),过了好久才显示出来,我看了看,都对---,我没装软驱,光驱的型号也有说明.我郁闷了,问题出现在那里?然道是我刻的盘有问题?其他的能好好地用,就这项不能?郁闷.
配置:内存:512. SATA:80G分为:四个区:C :NTFS10 GD :NTFS 15 E :FAT32 26 F:FAT32 21文件类型是想在安装的时候重新分区和格式化的.但装都不能装,什么都做不了.塞扬2.4 865G 参考 http://www.softwareinreview.com/cms/content/view/60/ 谢谢楼上的兄弟,这是我从你发的那网址上找到的参考文献资料,各位可以共同学习学习.
The "CD not found" error before installation
If you have a Core 2 Duo-capable motherboard and are getting an error message about the installer not being able to find the CD/DVD after you have already booted from it, the problem is likely with your IDE controller. In some modern motherboards, the parallel ATA controller has been taken out of the chipset and moved to a third-party drive controller. That third party is JMicron, and this problem most famously occurs in the Asus P5B motherboard, though other brands and models can be affected as well.
First, it will help to do a quick workaround in your BIOS. Press the Del, F1, or F2 key to get into your system BIOS just after powering it on. There should be a message somewhere on the screen that tells you which key to press; if you are not sure, press all three repeatedly and you're sure to get there. Somewhere in the BIOS setup you should see an option for the JMicron drive controller ("Onboard Devices" in the P5B BIOS menu). Set it to AHCI mode, then save and exit the BIOS setup utility.
Boot from the openSUSE 10.2 CD 1 or DVD. You'll still get the same message, but now you're better enabled to work around it. Press Enter to get past the error message, then choose your language in the following screen. That will bring you to the main menu. Use the down arrow key to select the Kernel Modules option and press Enter. In the next screen press Enter again to select the default option for IDE/RAID/SCSI Modules. In the long list that follows, find both the JMicron and the Generic IDE drivers, select them, press Enter, then press Enter again when you're asked for special options to pass to them. You will have to do this twice -- one time for each driver. When you return to the kernel module screen, use the Tab or arrow keys to select Back, and press Enter. That should put you back into the Main Menu. Now select the option for Start Installation or System and press Enter, then select Start Installation or Update and press Enter, and lastly select the CD-ROM as the source and press Enter. The normal graphical installation procedure will commence.
If the above does not work, write down installation source mirror addresses from the link in the installation source section below and use them to install openSUSE over FTP. The only difference in the procedure will be to change the above instructions to select FTP instead of CD-ROM as the source.
页:
[1]