再问cs8900a问题
Your elf file is little endian.arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x806ed60
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
tapif_init:open: Permission denied
-----------------------------------------------------------
NOTICE: you should be root at first !!!
NOTICE: you should inmod linux kernel net driver tun.o!!!
NOTICE: if you don't make device node, you should do commands:
NOTICE: mkdir /dev/net; mknod /dev/net/tun c 10 200
NOTICE: now the net simulation function can not support!!!
NOTICE: Please read SkyEye.README and try again!!!
-----------------------------------------------------------
failed to setup_module (name:net, type:cs8900a)
lcd_mod:1
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./initrd.img
start addr is set to 0xc0008000 by exec file.
Linux version 2.6.14 (francois@francois-laptop) (gcc version 3.3.2) #4 Fri May 1 18:12:31 CST 2009
CPU: ARM920Tid(wb) revision 0 (ARMvundefined/unknown)
Machine: SMDK2410
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410 (id 0x32410000)
S3C2410: core 62.400 MHz, memory 62.400 MHz, peripheral 62.400 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: mem=32M console=ttySAC0 root=/dev/ram initrd=0xc0800000,0x00800000 ramdisk_size=8192 rw
PID hash table entries: 256 (order: 8, 4096 bytes)
timer tcon=00000000, tcnt cb1f, tcfg 00000200,00000000, usec 0000189e
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 22272KB available (1556K code, 291K data, 96K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
softlockup thread 0 started up.
Freeing initrd memory: 8192K
NET: Registered protocol family 16
S3C2410: Initialising architecture
Console: switching to colour frame buffer device 80x25
fb0: Virtual frame buffer device, using 1024K of video memory
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
ERROR: s3c2410x_io_write_word(0x1900030a) = 0x00000000
eth0: incorrect signature 0xffff
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 4096KiB into ram disk... done.
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 96K
ifconfig: SIOCSIFADDR: No such device
/bin/ash: can't access tty; job control turned off
注释的地方都是什么意思啊？是我内核配置的问题？还是我的文件系统制作时的我问题？我查看了我的配置，该有的我都有了...... /dev 里面的设备有问题？
回复 1# boy0673 的帖子
两个问题：1. 阅读如下警告：
NOTICE: you should be root at first !!!
NOTICE: you should inmod linux kernel net driver tun.o!!!
NOTICE: if you don't make device node, you should do commands:
NOTICE: mkdir /dev/net; mknod /dev/net/tun c 10 200
NOTICE: now the net simulation function can not support!!!
NOTICE: Please read SkyEye.README and try again!!!
你应该用root用户运行这个示例，因为在运行网卡模拟的时候，需要插入tun.o的内核模块
回复 3# ksh 的帖子
在做根文件系统时，把mkdir /dev/net; mknod /dev/net/tun c 10 200已经做了问题主要出在：没有tun.o, 而生成tun.o模块需要重新配置内核...
两个问题：
1， 我配置内核时 make menuconfig， 不认识network driver 里能生成tun.o的相关项目...
2，是不是生成tun.o模块后，在重新把这个模块添加到initrd.img里，运行skyeye，insmod？
请高手予以指点... 我错了...真得是权限问题啊....苦死我了..
sudo skyeye -evmlinux
... ...
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
eth0: CS8900A rev D at 0xe0000300 irq=53, no eeprom , addr: 08: 0:3E:26:0A:5B
... ....
看来我的内核配置绝对没有问题...但是我想再问一下怎么在内核配置里编译出tun.o这种模块文件...相应的配置项目是？
[ 本帖最后由 boy0673 于 2009-5-2 17:26 编辑 ]
页:
[1]