网卡问题8139
我的网卡可以给LINUX认出来，可是一接入网线就会死机，能给我些建议吗？hosts file
10.0.0.10 xn.127.0.0.1 xn
127.0.0.1 localhost
10.172.99.30 xn.127.0.0.1 xn
network file
HOSTNAME=xn.127.0.0.1
NETWORKING=yes
$ su
Password:
# ifconfig
eth0 Link encap:EthernetHWaddr 00:40:CA:BF:CF:CB
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b)TX bytes:0 (0.0 b)
Interrupt:9 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1Mask:255.0.0.0
UP LOOPBACK RUNNINGMTU:16436Metric:1
RX packets:130 errors:0 dropped:0 overruns:0 frame:0
TX packets:130 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8488 (8.2 Kb)TX bytes:8488 (8.2 Kb)
# dmesg
Linux version 2.4.21-0.13mdk ([email protected]) (gcc version 3.2.2 (Mandrake Linux 9.1 3.2.2-3mdk)) #1 Fri Mar 14 15:08:06 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000def0000 (usable)
BIOS-e820: 000000000def0000 - 000000000deff000 (ACPI data)
BIOS-e820: 000000000deff000 - 000000000df00000 (ACPI NVS)
BIOS-e820: 000000000df00000 - 000000000e000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
224MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 57344
zone(0): 4096 pages.
zone(1): 53248 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=308 devfs=mount acpi=off quiet
No local APIC present or hardware disabled
Initializing CPU#0
Detected 1493.967 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2981.88 BogoMIPS
Memory: 223344k/229376k available (1410k kernel code, 5576k reserved, 1118k data, 136k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000
CPU: Common caps: 3febf9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.50GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030122
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xfd9ae, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS at 00:02.0
PCI: Found IRQ 5 for device 00:02.6
PCI: Sharing IRQ 5 with 00:02.7
PCI: Found IRQ 9 for device 00:08.0
PCI: Sharing IRQ 9 with 00:0c.0
PCI: Sharing IRQ 9 with 00:0d.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
vesafb: framebuffer at 0xe8000000, mapped to 0xce800000, size 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at cbc0:0008
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (800x600, 25593 bytes).
Console: switching to colour frame buffer device 80x16
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PCI: Enabling device 00:02.6 (0000 -> 0001)
PCI: Found IRQ 5 for device 00:02.6
PCI: Sharing IRQ 5 with 00:02.7
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SiS650 ATA 100 controller
ide0: BM-DMA at 0x1020-0x1027, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1028-0x102f, BIOS settings: hdc:pio, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
blk: queue c03cb420, I/O limit 4095Mb (mask 0xffffffff)
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS=2432/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 109k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting.Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 10 for device 00:02.2
usb-ohci.c: USB OHCI at membase 0xd0932000, IRQ 10
usb-ohci.c: usb-00:02.2, Silicon Integrated Systems 7001
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal
Adding Swap: 457812k swap-space (priority -1)
hub.c: new USB device 00:02.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x5e3/0x1205) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.00 Mouse on usb1:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
NTFS driver 2.1.1a .
NTFS volume version 3.1.
MSDOS FS: IO charset utf8
NTFS volume version 3.1.
ohci1394: $Rev: 693 $ Ben Collins <[email protected]>
PCI: Enabling device 00:0d.0 (0010 -> 0012)
PCI: Found IRQ 9 for device 00:0d.0
PCI: Sharing IRQ 9 with 00:08.0
PCI: Sharing IRQ 9 with 00:0c.0
ohci1394_0: Unexpected PCI resource length of 1000!
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=MMIO=Max Packet=
ieee1394: SelfID completion called outside of bus reset!
ieee1394: Host added: NodeGUID
8139too Fast Ethernet driver 0.9.26
PCI: Enabling device 00:08.0 (0000 -> 0003)
PCI: Found IRQ 9 for device 00:08.0
PCI: Sharing IRQ 9 with 00:0c.0
PCI: Sharing IRQ 9 with 00:0d.0
eth0: RealTek RTL8139 Fast Ethernet at 0xd09fa000, 00:40:ca:bf:cf:cb, IRQ 9
eth0:Identified 8139 chip type 'RTL-8139C'
inserting floppy driver for 2.4.21-0.13mdk
floppy0: no floppy controllers found
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Linux Kernel Card Services Kernel Version
options:
PCI: Found IRQ 9 for device 00:0c.0
PCI: Sharing IRQ 9 with 00:08.0
PCI: Sharing IRQ 9 with 00:0d.0
Yenta IRQ list 0898, PCI irq9
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
Installing knfsd (copyright (C) 1996 [email protected]).
Intel 810 + AC97 Audio, version 0.24, 15:29:58 Mar 14 2003
PCI: Enabling device 00:02.7 (0000 -> 0001)
PCI: Found IRQ 5 for device 00:02.7
PCI: Sharing IRQ 5 with 00:02.6
i810: SiS 7012 found at IO 0x1800 and 0x1c00, MEM 0x0000 and 0x0000, IRQ 5
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG16 (ALC200/200P)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
Splash status on console 0 changed to off
ide-floppy driver 0.99.newide
# 笔记本吗?
搞不定
页:
[1]