Redhat 9.0 声卡驱动OSS
OSS声卡驱动已经出来啊!!oss397h-redhat9.tar.gz"
target="_blank">www.linuxsir.org/software/oss397h-redhat9.tar.gz
安装方法：
前提是要安装kernel-source的包，请在光盘中找出来。
#rpm -ivh kernel-source*.rpm
备份文件/etc/modules.conf
#cp /etc/modules.conf /etc/modules.conf
如果您以前的声卡能用，但声音不好听，或者在/etc/modules.conf文件有关于声卡的项
，都要注销掉。比如我的声卡中有如下的：
alias sound-slot-0 i810_audio
post-install sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -L >/dev/null
2>&1
|| :
pre-remove sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -S >/dev/null
2>&1 |
| :
就在这三行的前面加#号注掉，或者删除。
一。建一个目录，比如是在/tmp目录下建一个ossound的目录，然后把oss397h-redhat9.
tar.gz复制到/tmp/ossound目录下；
二。解压：
#cd /tmp/oss
#./oss-install
三。驱动安装到哪里了呢？
注意仔细看你选择的安装目录，我是安装到了/usr/lib/oss这个目录。
四。因为oss是商业驱动，得破解license.asc，用文本工具把oos的安装目录下的licens
e.asc内容完全清除，加上下面的内容。
----BEGIN PGP SIGNED MESSAGE-----
!serial=N02753959
!product=OSS_1
!options=ALL
!person=UNION
!organization=
[email protected]
!os=*
!sold_by=4Front
!support=2002
!upgrades=2004
!version=3.
!flags=99b57b52
-----BEGIN PGP SIGNATURE-----
Version: 2.6.3i
Charset: noconv
uN10NunionUNIONuni0NuNi0Nun10nunI0NunionUNi0nuNi0nUni0nUn1onUnio
nUni0nUn10nUnionUnI0Nun1onUN10NunionUn1OnUn1oNUni0nUn1oNuni0Nuni
0nUni0nun1OnUnionUNIONunionUN10nUni0nun10nuNi0nUn1ONuN1onUni0nUn
1onUn10nuNioN=
Un10n
-----END PGP SIGNATURE-----
五。OSS的设置工具
# soundconf
这里面有很多设置，比如说开机加载等，都在这里设置
#soundon
打开声卡
#soundoff
关掉声卡
对于Redhat 9.0还得打一个补丁给xmms，否则播放mp3没有声音
http://havardk.xmms.org/dist/xmms-1...2.7-21.i386.rpm
#rpm -vih xmms*.rpm
我还是好好的说吧：其实呢，OSS驱动是指声卡驱动，你没有它RedHat自己带的驱动可以
使用，但是你不可以有多声道！比如你用了xmms在听歌，你就不好用
gmplayer看碟了。也是说OSS的作用是让好多程序可以同时使用你的声卡！ 我的OSS声卡出现了这样的问题！
开机后进入X后弹出这样的一个对话框：具体显示为：Couldn't open mixer device /dev/sound/mixer
不知道什么原因！
请各位帮帮我！ 是呀，是呀，我也是，是不是不能把上面的某一句注掉，楼主出来救救我们呀，这怎么用呀，用不成呀
我已经是山穷水尽了，我的是RH9 ， 声卡是VIA8233的 ，装过ALSA了，试 过了不行，，系统自 带的开机后就格一声就再也不响了，没办法了呀，我只寄望于这个 OSS了，再不出声，我恨不得不用RH了， 还有这个问题呀，看看吧，是不是没破解掉？
# soundon
This copy of OSS is licensed to UNION
Failed to activate the driver
Probably caused by a technical problem.
See /usr/lib/oss/soundon.log for more info.
下面是 /usr/lib/oss/soundon.log 的内容：
5月 23 04:54:41 CST 2003
OSS build 3.9.7h-0304051449 (Linux-2.4.20-8 )
Kernel version: Linux programmer2 2.4.20-8 #1 Thu Mar 13 17:54:28 EST 2003 i686 i686 i386 GNU/Linux
Kernel signature: d275289c16f68c608d2cb97f3cb0d584
Modutils version: 2.4.22
04:54:43up 12 min,2 users,load average: 0.58, 0.42, 0.25
=== Running /usr/local/bin/soundon ===
Install directory: /usr/lib/oss
Picked sndshield from 2.4.20-8.gz
Warning: loading /usr/lib/oss/modules/sndshield will taint the kernel: non-GPL license - LGPL
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module sndshield loaded, with warnings
sndshield loaded OK
Warning: loading /usr/lib/oss/modules/soundbase will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module soundbase loaded, with warnings
soundbase loaded OK
Warning: loading /usr/lib/oss/modules/ac97 will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module ac97 loaded, with warnings
ac97 loaded OK
Warning: loading /usr/lib/oss/modules/pnp will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module pnp loaded, with warnings
pnp loaded OK
Warning: loading /usr/lib/oss/modules/via8233 will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module via8233 loaded, with warnings
via8233 loaded OK
********************************************************************
* You can safely ignore the above message about tainting the kernel.
* It is completely political and means just that the maintainers of
* of modutils package dislike software that is not distributed under
* an open source license.
********************************************************************
Module loading finished.
==== About to start the driver using the following config ===
# Use soundconf to edit this file.
/SECUREAUDIO OFF
/PCIIRQ 10
/IRQEXCLUDE 3 4
/DMAEXCLUDE 2
-PCI30591106 #VIA VT8233 AC97 audio
VIA8233 ON
++ pnpres.dat ++
++++
Get version: Read-only file system
Failed to activate the driver
++++ dmesg printout follows ++++
Linux version 2.4.20-8 ([email protected]) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Mar 13 17:54:28 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000015ff0000 (usable)
BIOS-e820: 0000000015ff0000 - 0000000015ffffc0 (ACPI data)
BIOS-e820: 0000000015ffffc0 - 0000000016000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
351MB LOWMEM available.
On node 0 totalpages: 90096
zone(0): 4096 pages.
zone(1): 86000 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda7 BOOT_IMAGE=vmlinuz
Initializing CPU#0
Detected 1395.678 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2785.28 BogoMIPS
Memory: 349908k/360384k available (1347k kernel code, 7912k reserved, 999k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000
CPU: Common caps: 3febf9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.40GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xe8964, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default at 00:11.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK4018GAP, ATA DISK drive
blk: queue c03c9f40, I/O limit 4095Mb (mask 0xffffffff)
hdc: QSI DVD-ROM SDR-083, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 78140160 sectors (40008 MB), CHS=4864/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1200, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0x1300, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0x1700, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:11.2-2, assigned address 2
input0: USB HID v1.00 Mouse on usb1:2.0
Adding Swap: 393552k swap-space (priority -1)
ohci1394: $Rev: 693 $ Ben Collins <[email protected]>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=MMIO=Max Packet=
ieee1394: SelfID completion called outside of bus reset!
ieee1394: Host added: NodeGUID
parport0: PC-style at 0x378
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.26
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xd688b000, 00:c0:9f:15:fb:3a, IRQ 10
eth0:Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
Linux Kernel Card Services 3.1.22
options:
Yenta IRQ list 00b8, PCI irq11
Socket status: 30000006
spurious 8259A interrupt: IRQ7.
Yenta IRQ list 00b8, PCI irq9
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
parport0: PC-style at 0x378
lp0: using parport0 (polling).
lp0: console ready
ide-floppy driver 0.99.newide
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
Via 686a/8233/8235 audio driver 1.9.1-ac2
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 00:11.5 to 64
ac97_codec: AC97 Modem codec, id: CXT41 (Unknown)
via82cxxx: board #1 at 0xE100, IRQ 10
OssProbe: 1
Via 686a/8233/8235 audio driver 1.9.1-ac2
PCI: Unable to reserve I/O region #1:100@e100 for device 00:11.5
PCI: Unable to reserve I/O region #1:100@e100 for device 00:11.5
Via 686a/8233/8235 audio driver 1.9.1-ac2
PCI: Unable to reserve I/O region #1:100@e100 for device 00:11.5
PCI: Unable to reserve I/O region #1:100@e100 for device 00:11.5
++++
----BEGIN PGP SIGNED MESSAGE-----
!serial=N02753959
!product=OSS_1
!options=ALL
!person=UNION
!organization=
[email protected]
!os=*
!sold_by=4Front
!support=2002
!upgrades=2004
!version=3.
!flags=99b57b52
-----BEGIN PGP SIGNATURE-----
Version: 2.6.3i
Charset: noconv
uN10NunionUNIONuni0NuNi0Nun10nunI0NunionUNi0nuNi0nUni0nUn1onUnio
nUni0nUn10nUnionUnI0Nun1onUN10NunionUn1OnUn1oNUni0nUn1oNuni0Nuni
0nUni0nun1OnUnionUNIONunionUN10nUni0nun10nuNi0nUn1ONuN1onUni0nUn
1onUn10nuNioN=
Un10n
-----END PGP SIGNATURE-----
:cry::cry::cry::cry::cry::cry::cry::cry::cry: 那个license应该是破解调的，我和我的同学都可以用呀，为什么你们不可以呢？ 我来在贴一遍
----BEGIN PGP SIGNED MESSAGE-----
Copyright (C) 4Front Technologies. All rights reserved.
!serial=N02753959
!product=OSS_1
!options=ALL
!person=UNION
!organization=
[email protected]
!os=*
!sold_by=4Front
!support=2002
!upgrades=2004
!version=3.
!flags=99b57b52
-----BEGIN PGP SIGNATURE-----
Version: 2.6.3i
Charset: noconv
uN10NunionUNIONuni0NuNi0Nun10nunI0NunionUNi0nuNi0nUni0nUn1onUnio
nUni0nUn10nUnionUnI0Nun1onUN10NunionUn1OnUn1oNUni0nUn1oNuni0Nuni
0nUni0nun1OnUnionUNIONunionUN10nUni0nun10nuNi0nUn1ONuN1onUni0nUn
1onUn10nuNioN=
Un10n
-----END PGP SIGNATURE----- 我的是装完了之后重启一下然后在用soundconf配置，然后又重启了一下，就可义勇了 不错，我页安装成功了。有音，很好！谢谢Designer Designer
太谢谢了。太谢谢了。我都不知道在WINDOWS的音色有没有这么好呢！呵呵。
真的。对了，如何才能判断这个软件自己真的是激活了呢！这样了以后应该不会在有什么说你的声卡没有配好的情况吧！哈哈 问一下，如何一开机就加载呢！ 打quake 3(1.32b)的时候，声音很差！！！！
声音就像被加速了，叽哩咕鲁的,我的主板南桥是via8233a
页:
[1]