软件安装菜鸟问题!求助
我在安装声卡驱动时,解压后有六个文件:cmpcicmpci.cConfig.inConfigure.helpMakefileREADME.然后打入命令:./configure有错误为:bash: ./configure: No such file or directory.打入命令:make有错误为:Makefile:159: /Rules.make: No such file or directory make: *** No rule to make target `/Rules.make'.Stop.请问错误在哪里? 详细的操作方法请看readme,估计是直接make,然后将做好的*.o放到modules目录下,insmod *.o 我直接打ｍａｋｅ就有错误为：Makefile:159: /Rules.make: No such file or directory make: *** No rule to make target `/Rules.make'. Stop. 你还是将readme贴出来看看吧 Audio driver for CM8338/CM8738 chips by Chen-Li TienHARDWARE SUPPORTED
================================================================================
C-Media CMI8338
C-Media CMI8738
On-board C-Media chips
STEPS TO BUILD DRIVER
================================================================================
1. Backup the Config.in and Makefile in the sound driver directory
(/usr/src/linux/driver/sound).
The Configure.help provide help when you config driver in step
4, please backup the original one (/usr/src/linux/Document) and
copy this file.
The cmpci is document for the driver in detail, please copy it
to /usr/src/linux/Document/sound so you can refer it. Backup if
there is already one.
2. Extract the tar file by 'tar xvzf cmpci-xx.tar.gz' in the above
directory.
3. Change directory to /usr/src/linux
4. Config cm8338 driver by 'make menuconfig', 'make config' or
'make xconfig' command.
5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI
driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.
For driver option, please refer 'DRIVER PARAMETER'
6. Compile the kernel if necessary.
7. Compile the modules by 'make modules'.
8. Install the modules by 'make modules_install'
INSTALL DRIVER
================================================================================
1. Before first time to run the driver, create module dependency by
'depmod -a'
2. To install the driver manually, enter 'modprobe cmpci'.
3. Driver installation for various distributions:
a. Slackware 4.0
Add the 'modprobe cmpci' command in your /etc/rc.d/rc.modules
file.so you can start the driver automatically each time booting.
b. Caldera OpenLinux 2.2
Use LISA to load the cmpci module.
c. RedHat 6.0 and S.u.S.E. 6.1
Add following command in /etc/conf.modules:
alias sound cmpci
also visit http://www.cmedia.com.tw for installation instruction.
DRIVER PARAMETER
================================================================================
Some functions for the cm8738 can be configured in Kernel Configuration
or modules parameters. Set these parameters to 1 to enable.
mpu_io: I/O ports base for MPU-401, 0 if disabled.
fm_io: I/O ports base for OPL-3, 0 if disabled.
spdif_inverse:Inverse the S/PDIF-in signal, this depends on your
CD-ROM or DVD-ROM.
spdif_loop: Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out
directly.
speakers: Number of speakers used.
use_line_as_rear:Enable this if you want to use line-in as
rear-out.
use_line_as_bass:Enable this if you want to use line-in as
bass-out.
modem: You will need to set this parameter if you want to use
the HSP modem. You need install the pctel.o, the modem
driver itself.
joystick: Enable joystick. You will need to install Linux joystick
driver.
页:
[1]