关于Fedora的问题
刚装完FEDORA,进控制中心的LINUX内核时候出现了问题.提示如下:由于以下错误,无法读取内核配置:
/usr/src/linux-2.4/drives/net/wan/config.in, 行84;
then
^parse error
你的内核源代码包含无效的 配置规则,或者你刚发现KDE内核配置程序的错误.
我该怎么解决呢? CONFIG.IN内容如下:
#
# wan devices configuration
#
mainmenu_option next_comment
comment 'Wan interfaces'
bool 'Wan interfaces support' CONFIG_WAN
if [ "$CONFIG_WAN" = "y" ]; then
# There is no way to detect a comtrol sv11 - force it modular for now.
if [ "$CONFIG_ISA" = "y" ]; then
dep_tristate 'Comtrol Hostess SV-11 support' CONFIG_HOSTESS_SV11 m
# The COSA/SRP driver has not been tested as non-modular yet.
dep_tristate 'COSA/SRP sync serial boards support' CONFIG_COSA m
fi
#
# COMX drivers
#
tristate 'MultiGate (COMX) synchronous serial boards support' CONFIG_COMX
if [ "$CONFIG_COMX" != "n" ]; then
dep_tristate ' Support for COMX/CMX/HiCOMX boards' CONFIG_COMX_HW_COMX $CONFIG_COMX
dep_tristate ' Support for LoCOMX board' CONFIG_COMX_HW_LOCOMX $CONFIG_COMX
dep_tristate ' Support for MixCOM board' CONFIG_COMX_HW_MIXCOM $CONFIG_COMX
dep_tristate ' Support for MUNICH based boards: SliceCOM, PCICOM (WelCOM)' CONFIG_COMX_HW_MUNICH $CONFIG_COMX
dep_tristate ' Support for HDLC and syncPPP protocols on MultiGate boards' CONFIG_COMX_PROTO_PPP $CONFIG_COMX
if [ "$CONFIG_LAPB" = "y" ]; then
dep_tristate ' Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_COMX
fi
if [ "$CONFIG_LAPB" = "m" ]; then
dep_tristate ' Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_LAPB
fi
dep_tristate ' Support for Frame Relay on MultiGate boards' CONFIG_COMX_PROTO_FR $CONFIG_COMX
fi
dep_tristate 'DSCC4 support' CONFIG_DSCC4 m
if [ "$CONFIG_DSCC4" = "m" ]; then
dep_bool ' Etinc PCISYNC features' CONFIG_DSCC4_PCISYNC $CONFIG_DSCC4
dep_bool ' GPIO and PCI #RST pins wired together' CONFIG_DSCC4_PCI_RST $CONFIG_DSCC4
fi
#
# Lan Media's board. Currently 1000, 1200, 5200, 5245
#
tristate 'LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards' CONFIG_LANMEDIA
#
# ATI's sync/async boards. Currently 2520, 4020, 4520, 8520 -- 0 in second digit means async only
#
tristate 'Aurora Technology, Inc. synchronous asynchronous PCI cards V2' CONFIG_ATI_XX20
# There is no way to detect a Sealevel board. Force it modular
dep_tristate 'Sealevel Systems 4021 support' CONFIG_SEALEVEL_4021 m
tristate 'SyncLink HDLC/SYNCPPP support' CONFIG_SYNCLINK_SYNCPPP
# Generic HDLC
tristate 'Generic HDLC layer' CONFIG_HDLC
if [ "$CONFIG_HDLC" != "n" ]; then
bool ' Raw HDLC support' CONFIG_HDLC_RAW
bool ' Raw HDLC Ethernet device support' CONFIG_HDLC_RAW_ETH
bool ' Cisco HDLC support' CONFIG_HDLC_CISCO
bool ' Frame Relay support' CONFIG_HDLC_FR
bool ' Synchronous Point-to-Point Protocol (PPP) support' CONFIG_HDLC_PPP
if [ "$CONFIG_LAPB" = "m" -a "$CONFIG_HDLC" = "m" -o "$CONFIG_LAPB" = "y" ]; then
bool ' X.25 protocol support' CONFIG_HDLC_X25
else
comment ' X.25/LAPB support is disabled'
fi
if [ "$CONFIG_PCI" != "n" ]; then
dep_tristate ' Cyclades-PC300 support (RS-232/V.35, X.21, T1/E1 boards)' CONFIG_PC300 $CONFIG_HDLC
if [ "$CONFIG_PC300" != "n" ]; then
if [ "$CONFIG_PPP" != "n" -a "$CONFIG_PPP_MULTLINK" != "n" -a "$CONFIG_PPP_SYNCTTY" != "n" -a "$CONFIG_HDLC_PPP" = "y" ];
then
bool ' Cyclades-PC300 MLPPP support' CONFIG_PC300_MLPPP
else
comment ' Cyclades-PC300 MLPPP support is disabled. You have to enable PPP, PPP_MULTILINK'
comment ' PPP_SYNCTTY and HDLC_PPP to use this package.'
fi
fi
fi
dep_tristate ' SDL RISCom/N2 support' CONFIG_N2 $CONFIG_HDLC
dep_tristate ' Moxa C101 support' CONFIG_C101 $CONFIG_HDLC
dep_tristate ' FarSync T-Series support' CONFIG_FARSYNC $CONFIG_HDLC
bool ' Debug received/transmitted packets' CONFIG_HDLC_DEBUG_PKT
bool ' Debug hard_header routines' CONFIG_HDLC_DEBUG_HARD_HEADER
bool ' Debug FECN/BECN conditions' CONFIG_HDLC_DEBUG_ECN
bool ' Debug RX/TX packet rings' CONFIG_HDLC_DEBUG_RINGS
fi
tristate 'Frame relay DLCI support' CONFIG_DLCI
if [ "$CONFIG_DLCI" != "n" ]; then
int ' Max open DLCI' CONFIG_DLCI_COUNT 24
int ' Max DLCI per device' CONFIG_DLCI_MAX 8
dep_tristate ' SDLA (Sangoma S502/S508) support' CONFIG_SDLA $CONFIG_DLCI
fi
# Wan router core.
if [ "$CONFIG_WAN_ROUTER" != "n" ]; then
bool 'WAN router drivers' CONFIG_WAN_ROUTER_DRIVERS
if [ "$CONFIG_WAN_ROUTER_DRIVERS" = "y" ]; then
dep_tristate ' Sangoma WANPIPE(tm) multiprotocol cards' CONFIG_VENDOR_SANGOMA $CONFIG_WAN_ROUTER
if [ "$CONFIG_VENDOR_SANGOMA" != "n" ]; then
bool ' WANPIPE Cisco HDLC support' CONFIG_WANPIPE_CHDLC
bool ' WANPIPE Frame Relay support' CONFIG_WANPIPE_FR
bool ' WANPIPE X.25 support' CONFIG_WANPIPE_X25
bool ' WANPIPE PPP support' CONFIG_WANPIPE_PPP
bool ' WANPIPE Multi-Port PPP support' CONFIG_WANPIPE_MULTPPP
fi
if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
dep_tristate ' Cyclom 2X(tm) cards (EXPERIMENTAL)' CONFIG_CYCLADES_SYNC $CONFIG_WAN_ROUTER_DRIVERS $CONFIG_ISA
if [ "$CONFIG_CYCLADES_SYNC" != "n" ]; then
bool ' Cyclom 2X X.25 support (EXPERIMENTAL)' CONFIG_CYCLOMX_X25
fi
fi
fi
fi
# X.25 network drivers
if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
dep_tristate 'LAPB over Ethernet driver (EXPERIMENTAL)' CONFIG_LAPBETHER $CONFIG_LAPB $CONFIG_X25
dep_tristate 'X.25 async driver (EXPERIMENTAL)' CONFIG_X25_ASY $CONFIG_LAPB $CONFIG_X25
fi
if [ "$CONFIG_X86" = "y" ]; then
tristate 'Granch SBNI12 Leased Line adapter support' CONFIG_SBNI
if [ "$CONFIG_SBNI" != "n" ]; then
bool ' Multiple line feature support' CONFIG_SBNI_MULTILINE
fi
fi
fi
endmenu 我看完了！ :mrgreen: 你要配置内核吗？
还是自己编译吧。
页:
[1]