贴个我的dmesg结果给大家看看，好像有好多驱动没有加载！
我不知道怎么做了！Linux version 2.6.2 (root@CW) (gcc version 3.3.2 20031022 (Red Hat Linux 3.3.2-1)) #8 Mon Feb 9 23:25:14 CST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c0000 - 00000000000cc000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000b6f0000 (usable)
BIOS-e820: 000000000b6f0000 - 000000000b6ff000 (ACPI data)
BIOS-e820: 000000000b6ff000 - 000000000b700000 (ACPI NVS)
BIOS-e820: 000000000b700000 - 000000000b800000 (usable)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
184MB LOWMEM available.
On node 0 totalpages: 47104
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 43008 pages, LIFO batch:10
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f72b0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000LTP 0x00000000) @ 0x0b6fbfe4
ACPI: FADT (v001 VT8606 twisterT 0x06040000 PTL_ 0x000f4240) @ 0x0b6fef8c
ACPI: DSDT (v001 COMPAL CY23 0x06040000 MSFT 0x0100000d) @ 0x00000000
Building zonelist for node : 0
Kernel command line: ro root=/dev/hda8
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1194.131 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 181628k/188416k available (2768k kernel code, 6080k reserved, 1085k data, 156k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2351.10 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Celeron(TM) CPU 1200MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1193.0455 MHz.
..... host bus clock speed is 99.0454 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd80e, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040116
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller (gpe 6)
ACPI: PCI Interrupt Link (IRQs *10)
ACPI: PCI Interrupt Link (IRQs *11)
ACPI: PCI Interrupt Link (IRQs *5 9 10 11)
ACPI: PCI Interrupt Link (IRQs *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PPB_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ACPI: PCI Interrupt Link enabled at IRQ 10
ACPI: PCI Interrupt Link enabled at IRQ 11
ACPI: PCI Interrupt Link enabled at IRQ 11
ACPI: PCI Interrupt Link enabled at IRQ 5
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
IA-32 Microcode Update Driver: v1.13 <[email protected]>
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Installing knfsd (copyright (C) 1996 [email protected]).
NTFS driver 2.1.6 .
udf: registering filesystem
PCI: Disabling Via external APIC routing
ACPI: AC Adapter (on-line)
ACPI: Battery Slot (battery present)
ACPI: Power Button (FF)
ACPI: Lid Switch
ACPI: Processor (supports C1 C2, 16 throttling states)
ACPI: Thermal Zone (37 C)
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA ProSavage PM133/PL133/PN133 chipset
agpgart: Maximum main memory to use for agp memory: 143M
agpgart: AGP aperture is 64M @ 0xec000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
nbd: registered device at major 43
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 42) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 24X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1PCI: Enabling device 0000:00:07.2 (0010 -> 0011)
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: irq 11, io base 00001020
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
PCI: Setting latency timer of device 0000:00:07.5 to 64
hub 1-0:1.0: new USB device on port 1, assigned address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: SigmaTelModel: MP3UFD Rev: 0001
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 251904 512-byte hdwr sectors (129 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,type 0
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
ALSA device list:
#0: VIA 82C686A/B rev50 at 0x1400, irq 5
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
BIOS EDD facility v0.10 2003-Oct-11, 1 devices found
Please report your BIOS at http://domsch.com/linux/edd30/results.html
ACPI: (supports S0 S1 S3 S4 S5)
kjournald starting.Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 156k freed
hub 1-0:1.0: new USB device on port 2, assigned address 3
input: USB HID v1.10 Mouse on usb-0000:00:07.2-2
request_module: failed /sbin/modprobe -- char-major-162-0. error = 256
EXT3 FS on hda8, internal journal
Adding 265032k swap on /dev/hda7.Priority:-1 extents:1
kjournald starting.Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS volume version 3.1.
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Enabling device 0000:00:11.0 (0012 -> 0013)
eth0: ADMtek Comet rev 17 at 0xcc096c00, 00:90:96:25:FC:19, IRQ 11.
request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
request_module: failed /sbin/modprobe -- net-pf-10. error = 256
request_module: failed /sbin/modprobe -- net-pf-10. error = 256
request_module: failed /sbin/modprobe -- net-pf-10. error = 256
发现好多类似于：request_module: failed /sbin/modprobe -- char-major-10-134这样的消息！看得我头大，不知道是什么设备！我把所有的驱动都放到内核了！ 运行的还好，一切正常，声音啊，上网啊，都很好！也比以前的2.4.24稳定了，以前的老是好好的死机！ 还有个小问题， grub.conf中然 root=LABLE=/ 一定要改成 root=/dev/hda8才能启动，以前的2.4.24可没有这个要求！不知何故！ 下面这一段我看了头最大，说什么XFree86有BUG ，也不知道怎么办才好！哪 里有XFee86下载啊，没BUG的那种！
request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
我编译2.6.2后启动也有这个问题，如下：
atkbd.c: Unknown key released (translated set 0, code 0x2b on isa0060/serio0).
atkbd.c: Use 'setkeycodes 2b <keycode>' to make it.
atkbd.c: Unknown key pressed (translated set 0, code 0x41 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 41 <keycode>' to make it.
不过一切正常。希望高手指点。
grub.conf中然 root=LABLE=/ 一定要改成 root=/dev/hda8才能启动，以前的2.4.24可没有这个要求！不知何故！
2.4.24种好像也要这样吧。
request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
不知道你编译内核时有没有选APM支持。 没有apm支持，听说这样有些笔记本的电池管理会没有。
我的就是，不过gkrellm2倒可以显示出电池电量^_^。
下次我会把apm编进去。
request_module: failed /sbin/modprobe -- char-major-10-134. error = 256
不知道你编译内核时有没有选APM支持。
选了APM，我是笔记本的！ 您的电脑中 ACPI 没有安装完整。可能 ACPI 已启用，但是一些子选项没有启用 - 您至少需要启用“交流电源适配器”和“控制方式电池”并重编译内核。
已选了APM,APM的子项没选，还是这样，是不是子项也要选啊？ 我都选择了！可是错误还是有！ atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
这些错误怎么去呢?
页:
[1]