help, about my net?
# skyeye linux-2.4.x/linuxGNU gdb 5.3
Copyright 2002 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB.Type "show warranty" for details.
***************************************************************
************ SkyEye is Simulator based on GDB *************
***************************************************************
This SkyEye was configured as "--host=i686-pc-linux-gnu --target=arm-elf"...
(SkyEye) target sim
cpu info: armv3, arm7tdmi, 41007700, fff8ff00, 0
mach info: name at91, mach_init addr 0x813dd14
nic info: state=1, ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
nic_init_begin
tapif_init begin
tapif_init: fd 6
tapif_init: system("ifconfig tap0 inet 10.0.0.1");
sh: line 1: ifconfig: command not found
tapif_init end
nic_init_end
SKYEYE: use arm7100 mmu ops
Loaded ROM images/romfs.img
Connected to the simulator.
(SkyEye) 可能是因为你没有用root登陆的原因，因为你当前的搜索路径中没有包含ifconfig这个程序。你可以试着执行下面的语句：
export PATH=/sbin/:$PATH Now the detail is as follow:
# skyeye linux-2.4.x/linux
GNU gdb 5.3
Copyright 2002 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB.Type "show warranty" for details.
***************************************************************
************ SkyEye is Simulator based on GDB *************
***************************************************************
This SkyEye was configured as "--host=i686-pc-linux-gnu --target=arm-elf"...
(SkyEye) target sim
cpu info: armv3, arm7tdmi, 41007700, fff8ff00, 0
mach info: name at91, mach_init addr 0x813dad4
nic info: state=1, ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
nic_init_begin
tapif_init begin
tapif_init: fd 6
tapif_init: system("ifconfig tap0 inet 10.0.0.1");
tapif_init end
nic_init_end
SKYEYE: use arm7100 mmu ops
Loaded ROM images/romfs.img
Connected to the simulator.
(SkyEye) load
Loading section .init, size 0xa000 vma 0x1000000
Loading section .text, size 0xce860 vma 0x100a000
Loading section .data, size 0x8854 vma 0x10da000
Start address 0x1000000
Transfer rate: 7374240 bits/sec.
(SkyEye) run
Starting program: /usr/src/uClinux-dist/linux-2.4.x/linux
Linux version 2.4.22-uc0 (root@TristanHan) (gcc version 2.95.3 20010315 (release)(ColdFire patches - 20010318 from http://fiddes.net/coldfire/)(uClinux XIP and shared lib patches from http://www.snapgear.com/)) #3 一 5月 24 09:37:32 CST 2004
Processor: Atmel AT91M40xxx revision 0
Architecture: EB01
On node 0 totalpages: 1024
zone(0): 0 pages.
zone(1): 1024 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0
Calibrating delay loop... 15.82 BogoMIPS
Memory: 4MB = 4MB total
Memory: 2996KB available (826K code, 175K data, 40K init)
Dentry cache hash table entries: 512 (order: 0, 4096 bytes)
Inode cache hash table entries: 512 (order: 0, 4096 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 1024 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Atmel USART driver version 0.99
ttyS0 at 0xfffd0000 (irq = 2) is a builtin Atmel APB USART
ttyS1 at 0xfffcc000 (irq = 3) is a builtin Atmel APB USART
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 1400000-14A4FFF (RO)
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (romfs filesystem) readonly.
Shell invoked to run file: /etc/rc
Command: hostname GDB-ARMulator
Command: /bin/expand /etc/ramfs.img /dev/ram0
Command: mount -t proc proc /proc
Command: mount -t ext2 /dev/ram0 /var
Command: mkdir /var/tmp
Command: mkdir /var/log
Command: mkdir /var/run
Command: mkdir /var/lock
Command: mkdir /var/empty
Command: cat /etc/motd
Welcome to
____ __
/__| ||_|
_ _| || | _ _____ ___
| | | | || || |_ \| | | |\ \/ /
| |_| | |__| || | | | | |_| |/ \
|___\____|_||_|_| |_|\____|\_/\_/
| |
|_|
GDB/ARMulator support by <[email protected]>
For further information check:
http://www.uclinux.org/
Execution Finished, Exiting
Sash command shell (version 1.1.1)
/> ifconfig 10.0.0.1
ifconfig: ifconfig was not compiled with interface status display support.
pid 13: failed 256
/>
Who can know the reason, thanks! 那是因为你的initrd.img中没有ifconfig这个命令，你可以下载一个testsuite中ep7312的initrd.img试一下，或者你自己用busybox做一个放进去，也可以。 Thanks brothers, i solved this problem by unlinux4skyeye, thanks again! brothers,please share your result, I meet this problem too!!!\
help me!!
页:
[1]