RH9.0不支持NForce2网卡吗？
如果不支持该怎么安装，望高手指点啊 nForce2板带的？ 不支持，可以到NVIDIA官方网站去找驱动。 :-) 是啊。。，我去官方网站看了，没找到。 找到了http://download.nvidia.com/XFree86/nforce/1.0-0274/NVIDIA_nforce-1.0-0274.tar.gz 网上有驱动……
不过我下载下来从来没有安装成功过
编译内核到2.4.22以上就可以了，至于为什么，我也说不清，自己菜了……
解决方法：
1.下载驱动，安装，如果实在不成功，编译内核到2.6（现在流行这个 :-D ）
肯定行，不行就是RPWT :lol:
2.换个版本，Enterprise AS3 不错，现在机器都不差，装上，安装驱动，百试百灵
我的配置见签名，希望对你有点帮助哦…… 晕了
偶也是啊
倒
NF7-S
倒了偶
怎么升级内核啊？！
偶菜的一塌糊涂啊
高手讲仔细个啊
晕啊
残酷啊 下载NFORCE-Linux-x86-1.0-0301-pkg1.run，没有到http://www.nvidia.com/content/drivers/drivers.asp下载，然后在控制台上安装:sh NFORCE-Linux-x86-1.0-0301-pkg1.run，编辑/etc/modules.conf，修改alias eth0 forcedeth为# alias eth0 forcedeth，增加alias eth0 nvnet，再配置网卡的ip等等!!!! 我的是nf2就是按上超做成功的。。。。。。。。。。
官方原文:
Configuration
The installer does not update configuration files.After installing the drivers, configure the system to use the drivers by using the distribution's built-in configuration mechanisms for networking and sound, or edit the required files manually.
Module Configuration File Location
Module configuration files are different for 2.4 and 2.6 series kernels. The various Linux distributions also differ in how they handle module configuration.
For distributions based on a 2.4 series kernel, the module configuration file is typically called /etc/modules.conf.
For distributions based on a 2.6 series kernel, the module configuration file is typically called /etc/modprobe.conf. Some distributions use a subdirectory, /etc/modprobe.d/ , to hold individual configuration files for sound modules, etc.
Configuring the network driver
SuSE
For SuSE Linux Enterprise Server 9, use YaST to configure the network driver. Start the YaST GUI, select "Network Devices", then select "Network Card". This should bring up the "Network cards configuration" dialog.
Select "Other (not detected)", then select the "Configure" button. In the "Kernel Module" section, set "Module Name" to "nvnet", then select the "Next" button. Configure the interface parameters as required, select the "Next" button to return to the card configuration dialog, and select "Finish".
Red Hat
For Red Hat Enterprise Linux version 3,Red Hat 8, Red Hat 9 and Fedora Core 1, follow the instructions in other distributions to edit the configuration file /etc/modules.conf. Once this is done, configure the network interface parameters using the Network Configuration tool on the System Settings menu. The configuration tool can also be launched directly as "neat".
For Fedora Core 2, follow the instructions in other distributions to edit the configuration file /etc/modprobe.conf. Once this is done, configure the network interface parameters using the Network Configuration tool on the System Settings menu. The configuration tool can also be launched directly as "neat".
Mandrake
For Mandrake 10, use Mandrake Control Center (available via the mcc command) to configure the network driver. Select "Network & Internet", then select "New Connection". Select "LANConnection", select"Next", then select "Manual Choice".From the list of available network drivers, select "nvnet", then select "Next". and select "autoprobe". At this point, the driver will be configured and a new interface made availabe; select the newly-added interface to configure IP address settings, etc.
For earlier Mandrake distributions, follow the instructions in other distributions to edit the configuration file /etc/modules.conf. Once this is done, Mandrake Control Center can be used to configure IP address settings, etc., on the network interface supported by nvnet.
Other distributions
If the distribution you are using provides a configuration mechanism for network drivers, use it to select the nvnet driver module for use with the nForce ethernet device, and to set the networking parameters (IP address, etc.) for the interface. Otherwise, manually edit the module configuration file.
If your configuration file already contains an entry for the forcedeth driver (an open-source network driver that supports the nForce network controller), that entry needs to be commented out with a # or removed:
# alias eth0 forcedeth
Add the following line to the configuration file:
alias eth0 nvnet
If your system has multiple ethernet interfaces, you may need to use 'eth1'or higher in place of 'eth0'. 将forcedeth网卡支持编入内核就行了。 还是FC4好
直接就认了
页:
[1]