supplicant & Mdc-ssd
论坛里关于这两个802.1x认证程序的贴子也不少了,可会出现认证错误这个问题,最终还是没有解决,我已经重装过很多次了,还是这样,有谁指点一下要怎么办?以下我的认证过程:
1.supplicant
# supplicant eth1 usrname password
Interface number: 2
eth1 is UP
Hardware address is 00:e0:4c:90:b0:e4
IP address is 192.168.97.204
Send Packet: EAPOL Start ....OK
Recv Packet: Request Identify ....OK
Send Packet: Response Identify....OK
Recv Packet: Request MD5_challenge ....Fail
#
2.mdc-ssd
# mdc-ssd
mdc-ssd options in effect:
nodetach # (from /etc/mdc-ssd/options)
logfd 1 # (from /etc/mdc-ssd/options)
dump # (from /etc/mdc-ssd/options)
TLSdebug # (from /etc/mdc-ssd/options)
TLSstate # (from /etc/mdc-ssd/options)
TLSbugs # (from /etc/mdc-ssd/options)
mdc-ssd: Can't open tls secret file /tls-secrets
mdc-ssd: Unable to configure Transport Layer Security (TLS).
mdc-ssd: 802.1X: txStart(port=1) (transmit an EAP start packet)
mdc-ssd: 802.1X: supp state -> SSM_CONNECTING for port 1
mdc-ssd: 802.1X: EAP request-ID received.
mdc-ssd: mdc-ssd: txRspId(Transmit our identity (usrname) to authenticator)
mdc-ssd: 802.1X: supp state -> SSM_ACQUIRED for port 1
mdc-ssd: 802.1X: Received a authentication request packet with authentication type: 4.
mdc-ssd: txRspAuth: Duplicate authentication request seen, sending previous response.
mdc-ssd: 802.1X: supp state -> SSM_AUTHENTICATING for port 1
mdc-ssd: 802.1X: Received a authentication request packet with authentication type: 4.
mdc-ssd: txRspAuth: Duplicate authentication request seen, sending previous response.
mdc-ssd: 802.1X: supp state -> SSM_AUTHENTICATING for port 1
mdc-ssd: 802.1X: EAP failure received.
mdc-ssd: 802.1X: supp state -> SSM_HELD for port 1
mdc-ssd: 802.1X: EAP failure received.
请教这是为什么啊????????????????????????????? 哪个帅哥知道啊?快教教偶! 朋友，贴出安装说明，好吗？ :mrgreen: 好吧!安装过程都背得不能再熟了!
1.SUPPLICANT
修改hustauth文件,修改用户名和密码
#vi hustauth
改好了以后
#./install.sh
这就行啦,在终端中运行hustauth
2.mdc-ssd
安装RPM包
#RPM -Uvh mdc-ssd-01.1.2-1.i386.rpm --nodeps
#cd /etc/lib
#ln -s libssl.so libssl.so.1
#ln -s libcrypto.so libcrypto.so.1
#cd /etc/mdc-ssd
#vi ifcfg(修改用户名和密码)
#cd eth0
#vi chap-secrets(修改用户名和密码)
#mdc-ssd
~~~~~~~~~~~~就这样!
怎么认证会失败呢? 昏,看来这个问题是不会有答案了
页:
[1]