hxwtj 发表于 2002-12-18 23:10:12

安装了nvidia驱动,我进不了x-windows?????

我是安下面的方法安装的,做好所有的以后,每一步都成功的,当我重起是进红帽8.0
时,不能进去到x-window..

另外,我有个同学他在编译内kerenl不能成功,但是编译glx却可以成功,这是为什么?

描述:
nvidia3D显卡的for linux驱动,玩3D游戏必备! 安装方法:进入字符终端模式,unzip xxx.zip,先编译(rpm --rebuild或rpmbuild --rebuild)kernel,然后编译(rpm --rebuild或rpmbuild --rebuild)GLX,然后进入/usr/src/redhat/RPMS/i386(你的系统可能不是这个目录,但类似)目录下,rpm -ivh刚生成的两个rpm包.如果都succeful的话,则编辑/etc/X11/XF86Config-4(有的系统可能是/etc/XF86Config),将Driver "nv" (或Driver "vesa")改为Driver "nvidia" ,在Module section段,加上这一行:Load "glx";如果原来有这两行的话在前面加#注释掉:Load "dri"、Load "GLcore";同时,检查你的/etc/modules.conf文件里是否有alias char-major-10-175 agpgart和alias char-major-195 nvidia(这版本模块名字不再是NVdriver了)这两行,没有就加上,然后重起。


__________________________________________________________
爱linux:roll:

coolove 发表于 2002-12-18 23:14:54

什么错误

hxwtj 发表于 2002-12-18 23:44:53

进时......

进时,不能起动图形啊,过了一会儿,看到的是用英语出现在屏幕中的兰色长方中.
意思是好象是不能起动,问要不要重试.安yes or no确定.我多选了,都是不行.
   我同学的一次就成功拉,我按他的又该了XF86Config-4 ,还是不行

Kuye 发表于 2002-12-19 03:06:04

Re: 进时......

进时,不能起动图形啊,过了一会儿,看到的是用英语出现在屏幕中的兰色长方中.
意思是好象是不能起动,问要不要重试.安yes or no确定.我多选了,都是不行.
   我同学的一次就成功拉,我按他的又该了XF86Config-4 ,还是不行
我以前玩 Mandrake 9 时也经常碰到这种事情。。。的确莫名其妙,装完驱动后,重新启动 X,可是每次都是只有 nvidia 的图标闪了几下就退回到字符界面。。。可是偶尔重装后有时又可以。。。
不妨试一下:chmod 0666 /dev/nv* 然后 startx。
不行就再编译 nvidia-kernel,多编译几次(每次编译前先运行 make clean 把上次编译的 .o 全部删除),偶尔也可以通过。
两种方法要互相换。

如果还不行。。。重装一下 Linux。。。再装驱动。。。或许可以通过。。。。 :(
----------------------------
很奇怪啊,我在 mdk9 上难得成功,可是在 Gentoo 这个发行版上安装 n 卡驱动从来没有失败过。。。莫名其妙。。。 :?

hxwtj 发表于 2002-12-19 19:26:16

进不了x-window问题????

   我进不去的问题如下:
 (EE)NVIDIA (0):Failed to initialize the NVIDIA kerhel module!
   (EE)NVIDIA(0) :XXXAborting xxx
   (EE)Screen(s) found beet none have a usable confinguration.

   Fatal   Servererror:
   no screens found

Kuye 发表于 2002-12-20 02:00:54

Re: 进不了x-window问题????

   我进不去的问题如下:
 (EE)NVIDIA (0):Failed to initialize the NVIDIA kerhel module!
   (EE)NVIDIA(0) :XXXAborting xxx
   (EE)Screen(s) found beet none have a usable confinguration.

   Fatal   Servererror:
   no screens found
你的 nvidia-kernel 没装上去。OpenGL for X(GLX) 模块无法初始化核心模块所以会这样。
装上去就 OK 了。(问题就是 kernel 核心模块难装)

hxwtj 发表于 2002-12-20 20:37:11

我试了好多次......

我安装好多次,但每次都是是成功的,可就是就是不行,
是为什么nvidia-kernel安装不上呢,安装的时候又没有提示没有安上,哪怎么才可以安装上呢,我试好多遍,还重装了系统呢.

hxwtj 发表于 2002-12-20 20:38:02

我试了好多次......

我安装好多次,但每次都是是成功的,可就是就是不行,
是为什么nvidia-kernel安装不上呢,安装的时候又没有提示没有安上,哪怎么才可以安装上呢,我试好多遍,还重装了系统呢.

hxwtj 发表于 2002-12-22 21:14:28

我安装了NVIDIA驱动不知道怎么去卸掉?

   我安装的不是RPM包的,不知道卸掉,以前是RPM包的,进不了x-windows 我知道卸掉,但这个我知道。不好意思,一个好菜的问题,请大家帮帮忙?

jam 发表于 2002-12-23 00:06:44

我的mandrake9.0都是这样,下载了NVIDIA_GLX-1.0-4149.tar.gz和NVIDIA_kernel-1.0-4149.tar.gz装上,但键入STARTX,出现了NVIDIA的标志,之后硬盘就狂响,但怎样都进不了kde的桌面,在这过程中鼠标反应也变得迟钝,我的显卡是GEFORCE2 MX

oasis3322 发表于 2002-12-23 22:02:19

不幸

很不幸!我上述的问题都遇见过!第1次是无法启动XWINDOWS!下载TAR包重新安装!修改XF86Config中的"nv"后就解决了!第2次是启动到XWINDOWS时出现NVDIA商标!我想了好多办法都没解决!最后只有重装!
这次又出现了第1次遇见的问题!安装上次那个NVIDIA驱动!安装NVIDIA_GLX-1.0-3123.tar通过,在安装NVIDIA_kernel-1.0-3123.tar时报错!安装失败!试过很多次都没用!当然也进不了XWINDOWS了!


下面是我的XF86Config和XFree86.0的全部内容!请路过高手看看!配制是否正确!

XF86Config

# File generated by anaconda.

Section "ServerLayout"
      Identifier   "Anaconda Configured"
      Screen      0"Screen0" 0 0
      InputDevice    "Mouse0" "CorePointer"
        InputDevice        "Mouse1" "SendCoreEvents"
      InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"

# The location of the RGB database.Note, this is the name of the
# file minus the extension (like ".txt" or ".db").There is normally
# no need to change the default.

    RgbPath        "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.

    FontPath   "unix/:7100"

EndSection

Section "Module"
      Load"dbe"
      Load"extmod"
        Load"fbdevhw"
      Load"record"
      Load"freetype"
      Load"type1"
      Load"glx"
EndSection

Section "InputDevice"
      Identifier"Keyboard0"
      Driver      "keyboard"

#        Option        "AutoRepeat"        "500 5"

# when using XQUEUE, comment out the above line, and uncomment the
# following line
#        Option        "Protocol"        "Xqueue"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#        Option        "Xleds"                "1 2 3"

# To disable the XKEYBOARD extension, uncomment XkbDisable.
#        Option        "XkbDisable"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).For example, for a non-U.S.
# keyboard, you will probably want to use:
#        Option        "XkbModel"        "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#        Option        "XkbModel"        "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#        Option        "XkbLayout"        "de"
# or:
#        Option        "XkbLayout"        "de"
#        Option        "XkbVariant"        "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#        Option        "XkbOptions"        "ctrl:swapcaps"
        Option        "XkbRules"        "xfree86"
        Option        "XkbModel"        "pc105"
        Option        "XkbLayout"        "us"
        #Option        "XkbVariant"        ""
        #Option        "XkbOptions"        ""
EndSection

Section "InputDevice"
      Identifier"Mouse0"
      Driver      "mouse"
      Option      "Protocol" "IMPS/2"
      Option      "Device" "/dev/psaux"
      Option      "ZAxisMapping" "4 5"
      Option      "Emulate3Buttons" "no"
EndSection


Section "InputDevice"
        Identifier        "Mouse1"
        Driver                "mouse"
        Option                "Device"                "/dev/input/mice"
        Option                "Protocol"                "IMPS/2"
        Option                "Emulate3Buttons"        "no"
        Option                "ZAxisMapping"                "4 5"
EndSection


Section "Monitor"
      Identifier   "Monitor0"
      VendorName   "Monitor Vendor"
      ModelName    "Monitor Model"
      HorizSync   30-70
      VertRefresh 50-160
      Option "dpms"

       
EndSection

Section "Device"
        # no known options
        Identifier   "NVIDIA GeForce 2 MX (generic)"
      Driver       "nvidia"
      VendorName   "NVIDIA GeForce 2 MX (generic)"
      BoardName   "NVIDIA GeForce 2 MX (generic)"
      
      #BusID
EndSection

Section "Screen"
        Identifier   "Screen0"
      Device       "NVIDIA GeForce 2 MX (generic)"
      Monitor      "Monitor0"
        DefaultDepth        24

        Subsection "Display"
              Depth       24
                Modes       "1024x768" "800x600" "640x480"
        EndSubsection

EndSection

Section "DRI"
        Mode 0666
EndSection


--------------------------------------------------------------------------------

XFree86.0.log

XFree86 Version 4.2.0 (Red Hat Linux release: 4.2.0-72) / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 23 January 2002
        If the server is older than 6-12 months, or if your card is
        newer than the above date, look for a newer version before
        reporting problems.(See http://www.XFree86.Org/)
Build Operating System: Linux 2.4.18-11smp i686
Build Host: daffy.perf.redhat.com

Module Loader present
OS Kernel: Linux version 2.4.18-14 ([email protected]) (gcc version 3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Wed Sep 4 13:35:50 EDT 2002
Markers: (--) probed, (**) from config file, (==) default setting,
         (++) from command line, (!!) notice, (II) informational,
         (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Dec 25 05:39:01 2002
(==) Using config file: "/etc/X11/XF86Config"
(==) ServerLayout "Anaconda Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "NVIDIA GeForce 2 MX (generic)"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "us"
(**) XKB: layout: "us"
(==) Keyboard: CustomKeycode disabled
(**) FontPath set to "unix/:7100"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 7

(II) Open APM successful
(II) Module ABI versions:
        XFree86 ANSI C Emulation: 0.1
        XFree86 Video Driver: 0.5
        XFree86 XInput driver : 0.3
        XFree86 Server Extension : 0.1
        XFree86 Font Renderer : 0.3
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.0.0
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x80000058, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,1130 card 8086,1130 rev 02 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,1131 card 0000,0000 rev 02 class 06,04,00 hdr 01
(II) PCI: 00:1e:0: chip 8086,244e card 0000,0000 rev 02 class 06,04,00 hdr 01
(II) PCI: 00:1f:0: chip 8086,2440 card 0000,0000 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:1f:1: chip 8086,244b card 0000,0000 rev 02 class 01,01,80 hdr 00
(II) PCI: 00:1f:2: chip 8086,2442 card 0000,0000 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1f:3: chip 8086,2443 card 0000,0000 rev 02 class 0c,05,00 hdr 00
(II) PCI: 00:1f:4: chip 8086,2444 card 0000,0000 rev 02 class 0c,03,00 hdr 00
(II) PCI: 01:00:0: chip 10de,0111 card 0000,0000 rev b2 class 03,00,00 hdr 00
(II) PCI: 02:01:0: chip 13f6,0111 card 13f6,0111 rev 10 class 04,01,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) PCI-to-PCI bridge:
(II) PCI-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus 0 I/O range:
        -1        0x00000000 - 0x0000ffff (0x10000) IX
(II) Bus 0 non-prefetchable memory range:
        -1        0x00000000 - 0xffffffff (0x0) MX
(II) Bus 0 prefetchable memory range:
        -1        0x00000000 - 0xffffffff (0x0) MX
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0c (VGA_EN is set)
(II) Bus 1 I/O range:
(II) Bus 1 non-prefetchable memory range:
        -1        0xdc000000 - 0xddffffff (0x2000000) MX
(II) Bus 1 prefetchable memory range:
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX
(II) Bus 2: bridge is at (0:30:0), (0,2,2), BCTRL: 0x06 (VGA_EN is cleared)
(II) Bus 2 I/O range:
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000c400 - 0x0000c4ff (0x100) IX
        -1        0x0000c800 - 0x0000c8ff (0x100) IX
        -1        0x0000cc00 - 0x0000ccff (0x100) IX
(II) Bus 2 non-prefetchable memory range:
(II) Bus 2 prefetchable memory range:
(II) Bus -1: bridge is at (0:31:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(--) PCI:*(1:0:0) NVidia GeForce2 MX 100/200 rev 178, Mem @ 0xdc000000/24, 0xd0000000/27
(II) Addressable bus resource ranges are
        -1        0x00000000 - 0xffffffff (0x0) MX
        -1        0x00000000 - 0x0000ffff (0x10000) IX
(II) OS-reported resource ranges:
        -1        0xffe00000 - 0xffffffff (0x200000) MX(B)
        -1        0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
        -1        0x000f0000 - 0x000fffff (0x10000) MX
        -1        0x000c0000 - 0x000effff (0x30000) MX
        -1        0x00000000 - 0x0009ffff (0xa0000) MX
        -1        0x0000ffff - 0x0000ffff (0x1) IX
        -1        0x00000000 - 0x000000ff (0x100) IX
(II) Active PCI resource ranges:
        -1        0xd8000000 - 0xd9ffffff (0x2000000) MX
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX(B)
        -1        0xdc000000 - 0xdcffffff (0x1000000) MX(B)
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000d800 - 0x0000d81f (0x20) IX
        -1        0x00005000 - 0x0000500f (0x10) IX
        -1        0x0000d000 - 0x0000d01f (0x20) IX
        -1        0x0000f000 - 0x0000f00f (0x10) IX
(II) Active PCI resource ranges after removing overlaps:
        -1        0xd8000000 - 0xd9ffffff (0x2000000) MX
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX(B)
        -1        0xdc000000 - 0xdcffffff (0x1000000) MX(B)
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000d800 - 0x0000d81f (0x20) IX
        -1        0x00005000 - 0x0000500f (0x10) IX
        -1        0x0000d000 - 0x0000d01f (0x20) IX
        -1        0x0000f000 - 0x0000f00f (0x10) IX
(II) OS-reported resource ranges after removing overlaps with PCI:
        -1        0xffe00000 - 0xffffffff (0x200000) MX(B)
        -1        0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
        -1        0x000f0000 - 0x000fffff (0x10000) MX
        -1        0x000c0000 - 0x000effff (0x30000) MX
        -1        0x00000000 - 0x0009ffff (0xa0000) MX
        -1        0x0000ffff - 0x0000ffff (0x1) IX
        -1        0x00000000 - 0x000000ff (0x100) IX
(II) All system resource ranges:
        -1        0xffe00000 - 0xffffffff (0x200000) MX(B)
        -1        0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
        -1        0x000f0000 - 0x000fffff (0x10000) MX
        -1        0x000c0000 - 0x000effff (0x30000) MX
        -1        0x00000000 - 0x0009ffff (0xa0000) MX
        -1        0xd8000000 - 0xd9ffffff (0x2000000) MX
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX(B)
        -1        0xdc000000 - 0xdcffffff (0x1000000) MX(B)
        -1        0x0000ffff - 0x0000ffff (0x1) IX
        -1        0x00000000 - 0x000000ff (0x100) IX
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000d800 - 0x0000d81f (0x20) IX
        -1        0x00005000 - 0x0000500f (0x10) IX
        -1        0x0000d000 - 0x0000d01f (0x20) IX
        -1        0x0000f000 - 0x0000f00f (0x10) IX
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "fbdevhw"
(II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a
(II) Module fbdevhw: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 0.0.2
        ABI class: XFree86 Video Driver, version 0.5
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.13.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension RECORD
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.1.10
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.0.1
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
        compiled for 4.0.2, module version = 1.0.3123
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) LoadModule: "nvidia"
(II) Loading /usr/X11R6/lib/modules/drivers/nvidia_drv.o
(II) Module nvidia: vendor="NVIDIA Corporation"
        compiled for 4.0.2, module version = 1.0.3123
        Module class: XFree86 Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 1.0.0
        Module class: XFree86 XInput Driver
        ABI class: XFree86 XInput driver, version 0.3
(II) NVIDIA XFree86 Driver1.0-3123Tue Aug 27 16:00:08 PDT 2002
(II) NVIDIA: NVIDIA driver for: RIVA TNT, RIVA TNT2, Vanta,
        RIVA TNT2 Ultra, RIVA TNT2 Model 64, Aladdin TNT2, GeForce 256,
        GeForce DDR, Quadro, GeForce2 MX/MX 400, GeForce2 MX 100/200,
        Quadro2 MXR/EX/Go, GeForce2 Integrated GPU, GeForce2 GTS,
        GeForce2 Ti, GeForce2 Ultra, Quadro2 Pro, GeForce4 MX 460,
        GeForce4 MX 440, GeForce4 MX 420, Quadro4 500/550 XGL,
        Quadro4 200/400 NVS, NV18, NV18 , NV18, NV18, NV18GL, NV18GL ,
        NV18GL, 0x01F0, GeForce3, GeForce3 Ti 200, GeForce3 Ti 500,
        Quadro DCC, GeForce4 Ti 4600, GeForce4 Ti 4400, GeForce4 Ti 4200,
        Quadro4 900 XGL, Quadro4 750 XGL, Quadro4 700 XGL, NV28, NV28 ,
        NV28GL, NV28GL , GeForce2 Go, GeForce4 440 Go, GeForce4 420 Go,
        GeForce4 420 Go 32M, GeForce4 460 Go, GeForce4 440 Go 64M,
        GeForce4 410 Go 16M, Quadro4 500 GoGL
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset GeForce2 MX 100/200 found
(II) resource ranges after xf86ClaimFixedResources() call:
        -1        0xffe00000 - 0xffffffff (0x200000) MX(B)
        -1        0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
        -1        0x000f0000 - 0x000fffff (0x10000) MX
        -1        0x000c0000 - 0x000effff (0x30000) MX
        -1        0x00000000 - 0x0009ffff (0xa0000) MX
        -1        0xd8000000 - 0xd9ffffff (0x2000000) MX
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX(B)
        -1        0xdc000000 - 0xdcffffff (0x1000000) MX(B)
        -1        0x0000ffff - 0x0000ffff (0x1) IX
        -1        0x00000000 - 0x000000ff (0x100) IX
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000d800 - 0x0000d81f (0x20) IX
        -1        0x00005000 - 0x0000500f (0x10) IX
        -1        0x0000d000 - 0x0000d01f (0x20) IX
        -1        0x0000f000 - 0x0000f00f (0x10) IX
(II) resource ranges after probing:
        -1        0xffe00000 - 0xffffffff (0x200000) MX(B)
        -1        0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
        -1        0x000f0000 - 0x000fffff (0x10000) MX
        -1        0x000c0000 - 0x000effff (0x30000) MX
        -1        0x00000000 - 0x0009ffff (0xa0000) MX
        -1        0xd8000000 - 0xd9ffffff (0x2000000) MX
        -1        0xd0000000 - 0xd7ffffff (0x8000000) MX(B)
        -1        0xdc000000 - 0xdcffffff (0x1000000) MX(B)
        0        0x000a0000 - 0x000affff (0x10000) MS
        0        0x000b0000 - 0x000b7fff (0x8000) MS
        0        0x000b8000 - 0x000bffff (0x8000) MS
        -1        0x0000ffff - 0x0000ffff (0x1) IX
        -1        0x00000000 - 0x000000ff (0x100) IX
        -1        0x0000c000 - 0x0000c0ff (0x100) IX
        -1        0x0000d800 - 0x0000d81f (0x20) IX
        -1        0x00005000 - 0x0000500f (0x10) IX
        -1        0x0000d000 - 0x0000d01f (0x20) IX
        -1        0x0000f000 - 0x0000f00f (0x10) IX
        0        0x000003b0 - 0x000003bb (0xc) IS
        0        0x000003c0 - 0x000003df (0x20) IS
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
        compiled for 4.2.0, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(--) NVIDIA(0): Linear framebuffer at 0xD0000000
(--) NVIDIA(0): MMIO registers at 0xDC000000
(EE) NVIDIA(0): Failed to initialize the NVdriver kernel module!
(EE) NVIDIA(0):*** Aborting ***
(II) UnloadModule: "nvidia"
(II) UnloadModule: "vgahw"
(II) Unloading /usr/X11R6/lib/modules/libvgahw.a
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found

When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to [email protected].

oasis3322 发表于 2002-12-23 22:08:13

安装NVIDIA_kernel-1.0-3123.tar失败的原因是什么?

Kuye 发表于 2002-12-24 06:15:23

推荐你改成 16 位色深,这样玩游戏的时候会快大约一倍。

安装NVIDIA_kernel-1.0-3123.tar失败的原因是什么?
天知道呢。。。有时候看起来安装成功了,可是 X 启动失败,还是等于安装失败。
我感觉只要安装 kernel 模块时最后提示中带了警告(非 GPL 的警告除外),就意味着这一次安装 100% 失败,就算没警告也不等于安装成功。
XF86Config-4 配置文件应该没什么关系。
多装几次试一下,偶尔多装几次就能成(有一次为了 nvidia-kernel 我一天重装了 5 次 mdk9...最后,哈哈,总算成了 <- 亏我还笑得出)
有一次 chmod 0666 /dev/nv* 也成。。。
有点凭运气的味道。
修改XF86Config中的"nv"后就解决了
改成 nv 或者禁用掉 glx 模块还不如不装,装了也是白装 -- 没有 OpenGL 3D 硬件加速啊~~~。

郁闷ing。。。
奇怪:可是 Gentoo 里我从来没遇见这个问题。。。

oasis3322 发表于 2002-12-25 20:22:55

我在安装NVIDIA_kernel-1.0-3123时出现Error 255的警告!
这又是什么原因?

hxwtj 发表于 2002-12-26 16:26:58

谢谢!!!哈哈

   我也只好再装系统拉!~~
  




   ………………………………………………
   linux我爱!!
页: [1] 2
查看完整版本: 安装了nvidia驱动,我进不了x-windows?????