skyeye1.2.9 串口问题 求助

skyeye_bf

调试skyeye1.2.9/testsuite/arm_hello例子时，如果用skyeye -e arm_hello则正常；
但是如果更改skyeye.conf中的uart模式为stdio时，会出现以下现象：
(skyeye)start
arch: arm
cpu info: armv3, arm7tdmi, 41007700, fff8ff00, 0
In do_mach_option, mach info: name at91, mach_init addr 0xb6f9af20

Invalid parameter for mod option
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm7100 mmu ops
exec file "arm_hello"'s format is elf32-i386.
load section .text: addr = 0x01000000  size = 0x00000084.
load section .glue_7: addr = 0x01000084  size = 0x00000000.
load section .glue_7t: addr = 0x01000084  size = 0x00000000.
load section .data: addr = 0x01002000  size = 0x00001000.
not load section .bss: addr = 0x01003000  size = 0x00000000 .
not load section .debug_abbrev: addr = 0x00000000  size = 0x0000004e .
not load section .debug_info: addr = 0x00000000  size = 0x00000187 .
not load section .debug_line: addr = 0x00000000  size = 0x000000a9 .
not load section .debug_pubnames: addr = 0x00000000  size = 0x0000001c .
not load section .debug_aranges: addr = 0x00000000  size = 0x00000020 .
In SIM_start, Set PC to the address 0x1000000

紧接着在(skyeye)提示符后，输入任何字母都无法显示出来，但是可以正常使用，
例如输入 run，虽然无法显示，但是会运行程序，输入后的结果显示如下：
(skyeye)(running)helloworldhelloworldhelloworldhelloworldhelloworld


问下？
1.出现下面情况的原因是什么？
not load section .bss: addr = 0x01003000  size = 0x00000000 .
not load section .debug_abbrev: addr = 0x00000000  size = 0x0000004e .
not load section .debug_info: addr = 0x00000000  size = 0x00000187 .
not load section .debug_line: addr = 0x00000000  size = 0x000000a9 .
not load section .debug_pubnames: addr = 0x00000000  size = 0x0000001c .
not load section .debug_aranges: addr = 0x00000000  size = 0x00000020 .

2.为何输入不会显示，虽然可以正常运行？
（补充一句，利用skyeye1.2版本时候可以正常回显和运行。）

skyeye_bf

忘了说运行环境了，Ubuntu 8.04.

liukui359

可以把你的skyeye.conf文件贴出来看下不?谢谢，我的这个测试例子打印不出来

skyeye_bf

arch:arm
cpu: arm7tdmi

mach: at91

mem_bank: map=M, type=RW, addr=0x01000000, size=0x00400000
mem_bank: map=I, type=RW, addr=0xf0000000, size=0x10000000
uart:mod=stdio
#log: logon=0, logfile=./sk1.log, start=0, end=200000

skyeye_bf

root@bf-desktop:/skyeye-1.2.9_rc1/testsuite/arm_hello# ls
Makefile  README  arm_hello  hello.c  hello.lds  skyeye.conf  start.S
root@bf-desktop:/skyeye-1.2.9_rc1/testsuite/arm_hello# skyeye -e arm_hello
SkyEye is an Open Source project under GPL. All rights of different parts or modules are reserved by their author. Any modification or redistributions of SkyEye should note remove or modify the annoucement of SkyEye copyright.
Get more information about it, please visit the homepage http://www.skyeye.org.
Type "help" to get command list.
pen_buffer not implemented.
(skyeye)start
arch: arm
cpu info: armv3, arm7tdmi, 41007700, fff8ff00, 0
In do_mach_option, mach info: name at91, mach_init addr 0xb6fa1f20

Invalid parameter for mod option
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm7100 mmu ops
exec file "arm_hello"'s format is elf32-i386.
load section .text: addr = 0x01000000  size = 0x00000084.
load section .glue_7: addr = 0x01000084  size = 0x00000000.
load section .glue_7t: addr = 0x01000084  size = 0x00000000.
load section .data: addr = 0x01002000  size = 0x00001000.
not load section .bss: addr = 0x01003000  size = 0x00000000 .
not load section .debug_abbrev: addr = 0x00000000  size = 0x0000004e .
not load section .debug_info: addr = 0x00000000  size = 0x00000187 .
not load section .debug_line: addr = 0x00000000  size = 0x000000a9 .
not load section .debug_pubnames: addr = 0x00000000  size = 0x0000001c .
not load section .debug_aranges: addr = 0x00000000  size = 0x00000020 .
In SIM_start, Set PC to the address 0x1000000

*在下面的(skyeye)后输入的run并没有显示，但却起了作用
(skyeye)(running)helloworldhelloworldhelloworldhelloworldhelloworldhelloworldhelloworld
先对热心的人表示下感谢！

[ 本帖最后由 skyeye_bf 于 2009-10-11 18:32 编辑 ]