虚拟拔号到底该怎么用？

三塘印月

redflag desktop 3.2
>rpm -e pppoe
>rpm -i pppoe               /*注：PPPoE (Point-to-Point Protocol over Ethernet)
驱动程序由LINUXFANS处下载*/
装完后发现里面有个163 263拔号，偏偏就是没有虚拟拔号，像M$ Windows 下面的enternet 300之类啊，

ivyharry

你用的是什么系统?
如果用的是RH9的话就很好办了
在"网络"里面新建一个XDSL联接就可以了!

三塘印月

redflag desktop 3.2

ivyharry

那就还是只有用PPPOE了
运行CONFIGE文件培植一个就好了~(如果你英文比较好的话应该可以看懂的!)

Leaves

你有没有设置你的网络设置呢?
这是red hat 中的adsl,自己看一看,

[code:1]#rpm -e rp-pppoe

解压和安装：
#tar zxvf rp-pppoe-3.5.tar.gz
进入解压目录执行
#sh ./go


然后再来设置ADSL。这一处，我们要用命令。

#adsl-setup


Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good! Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名

INTERFACE

>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):如果一张网卡就设置写上eth0

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):不用写什么

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:在这里写上202.96.134.133
下一个DNS是202.96.168.68

PASSWORD

>>> Please enter your PPPoE password:输入密码
>>> Please re-enter your PPPoE password:再输入一次

FIREWALLING

Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2):这里添写为2

** Summary of what you entered **

Ethernet Interface: eth0
User name: XXX
Activate-on-demand: No
DNS: Do not adjust
Firewalling: MASQUERADE

>>> Accept these settings and adjust configuration files (y/n)?

弄完后，就按一个y键。

用adsl-start来启动ADSL。如果不成功就重启一下计算机。[/code:1]

要是你设完了你的网络设备,那就看下面!

在"网络"里面新建一个XDSL联接就可以了!

可以用这个,看到xdsl激活它,也可以在命令下,#adsl-start
去ping (IP)能不能通,再ping DNS,要是能通的话,说明你成功了!!


adsl 相关的命令：

#adsl-start 打开ADSL
#adsl-stop 停止
#adsl-status 状态