|
|
楼主 |
发表于 2009-8-31 09:25:04
|
显示全部楼层
以下是Skyeye的运行情况
[root@localhost EXEC]# skyeye -e vmlinux
Your elf file is little endian.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x807c440
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
lcd_mod:1
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM ./initrd.img
exec file "vmlinux"'s format is elf32-little.
load section .init: addr = 0xc0008000 size = 0x00017000.
load section .text: addr = 0xc001f000 size = 0x0017a3b4.
not load section .pci_fixup: addr = 0xc01993b4 size = 0x00000000 .
not load section __ksymtab: addr = 0xc01993b4 size = 0x00000000 .
not load section __ksymtab_gpl: addr = 0xc01993b4 size = 0x00000000 .
not load section __kcrctab: addr = 0xc01993b4 size = 0x00000000 .
not load section __kcrctab_gpl: addr = 0xc01993b4 size = 0x00000000 .
load section __param: addr = 0xc01993b4 size = 0x0000026c.
load section .data: addr = 0xc019a000 size = 0x0002ff30.
not load section .bss: addr = 0xc01c9f40 size = 0x000158f8 .
not load section .comment: addr = 0x00000000 size = 0x00001cd4 .
call ARMul_InitSymTable,kernel filename is vmlinux.
start addr is set to 0xc0008000 by exec file.
Linux version 2.6.14 ([email protected]) (gcc version 3.4.1) #1 Mon Aug 31 09:13:12 CST 2009
CPU: ARM920Tid(wb) [41009200] revision 0 (ARMvundefined/unknown)
Machine: SMDK2410
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410 (id 0x32410000)
S3C2410: core 62.400 MHz, memory 62.400 MHz, peripheral 62.400 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: mem=32M console=ttySAC0 root=/dev/ram initrd=0xc0800000,0x00800000 ramdisk_size=8192
PID hash table entries: 256 (order: 8, 4096 bytes)
timer tcon=00000000, tcnt cb1f, tcfg 00000200,00000000, usec 0000189e
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 22272KB available (1513K code, 278K data, 92K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
softlockup thread 0 started up.
Freeing initrd memory: 8192K
NET: Registered protocol family 16
S3C2410: Initialising architecture
Console: switching to colour frame buffer device 80x25
fb0: Virtual frame buffer device, using 1024K of video memory
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
eth0: CS8900A rev D at 0xe0000300 irq=53, no eeprom , addr: 08: 0:3E:26:0A:5B
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 204
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 2048KiB [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 92K
init started: BusyBox v1.4.1 (2007-02-10 01:19:06 CST) multi-call binary
Starting pid 16, console /dev/console: '/etc/init.d/rcS'
mkdir: cannot create directory '/var/tmp': Read-only file system
mkdir: cannot create directory '/var/log': Read-only file system
mkdir: cannot create directory '/var/run': Read-only file system
mkdir: cannot create directory '/var/lock': Read-only file system
Welcome to
_ _____ __ __ _ _
/ / __ / _/ | | |_|
/ _ | | | | / / / | | _ ____ _ _ _ _
/ /_ | |__| | / / _/ | | | | _ | | | | / /
/ /___ | |__ | | | || |___ | | |_| | |_| |/
/_/ _| | _|_| |_||_____||_|_| |_|____|_/_/
ARMLinux for Skyeye:
For further information please check:
http://www.skyeye.org/
BusyBox v1.4.1 (2007-02-10 01:19:06 CST) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/ash: can't access tty; job control turned off
/ $ ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:3E:26:0A:5B
inet addr:10.0.0.2 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:53 Base address:0x300
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
/ $ ping -c 2 10.0.0.2
PING 10.0.0.2 (10.0.0.2): 56 data bytes
64 bytes from 10.0.0.2: icmp_seq=0 ttl=64 time=0.0 ms
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=0.0 ms
--- 10.0.0.2 ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.0/0.0/0.0 ms
/ $ ping -c 1 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
--- 10.0.0.1 ping statistics ---
1 packets transmitted, 0 packets received, 100% packet loss
/ $ |
|
IP卡
狗仔卡
发表于 2009-8-31 00:31:40
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2009-9-3 09:57:08