|
|
楼主 |
发表于 2005-8-1 23:54:41
|
显示全部楼层
Linux version 2.6.12.3 (root@MagicLinux) (gcc version 3.4.3 20041114 (
Magic Linux 3.4.3-3)) #1 Wed Jul 20 03:16:26 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fa8c0
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x0fff0
000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x0fff0
030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x0fff0
0c0
ACPI: DSDT (v001 VIA K7VT4 0x00001000 MSFT 0x0100000d) @ 0x00000
000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: ro root=/dev/hde5 vga=791 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1798.969 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 253664k/262080k available (3392k kernel code, 7772k reserved,
876k data, 284k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode.
.. Ok.
Calibrating delay loop... 3555.32 BogoMIPS (lpj=1777664)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 000000
00 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Sempron(tm) 2500+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c2
checking if image is initramfs... it is
Freeing initrd memory: 441k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfda71, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disa
bled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disa
bled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disa
bled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disa
bled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post
a report
Machine check exception polling timer started.
apm: BIOS not found.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFS: nTxBlock = 1987, nTxLock = 15897
SGI XFS with large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: framebuffer at 0xda000000, mapped to 0xd0980000, using 4096k,
total 4096k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:02e5
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
36270 bytes,<6>...found (1024x768, 19600 bytes, v3).
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
[drm] Initialized drm 1.0.0 20040925
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/91
5G chipsets
intelfb: Version 0.9.2
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabl
ed
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with ideb
us=xx
VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [LNKB] -> GSI 10 (level, l
ow) -> IRQ 10
VIA8237SATA: chipset revision 128
VIA8237SATA: 100% native mode on irq 10
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKA] -> GSI 11 (level, l
ow) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide2: BM-DMA at 0xfc00-0xfc07, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdg:DMA, hdh:DMA
Probing IDE interface ide2...
hde: ST3160021A, ATA DISK drive
hdf: ST34321A, ATA DISK drive
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide3...
hdg: ASUS CRW-4824A, ATAPI CD/DVD-ROM drive
hdh: SAMSUNG CD-ROM SC-152L, ATAPI CD/DVD-ROM drive
ide3 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide4...
Probing IDE interface ide5...
hde: max request size: 1024KiB
hde: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hde: cache flushes supported
hde: hde1 hde2 < hde5 hde6 hde7 hde8 hde9 hde10 hde11 >
hdf: max request size: 128KiB
hdf: 8404830 sectors (4303 MB) w/128KiB Cache, CHS=8894/15/63, UDMA(33
)
hdf: cache flushes not supported
hdf: hdf1 < hdf5 >
libata version 1.11 loaded.
usbmon: debugs is not available
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa.0
NET: Registered protocol family 26
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 UAR1 USB1 USB2 USB3 USB4 EHCI USBD PS2K AC9 MC9 ILAN SLPB
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 284k freed
ReiserFS: hde5: found reiserfs format "3.6" with standard journal
ReiserFS: hde5: using ordered data mode
ReiserFS: hde5: journal params: device hde5, size 8192, journal first
block 18, max trans len 1024, max batch 900, max commit age 30, max tr
ans age 30
ReiserFS: hde5: checking transaction log (hde5)
input: AT Translated Set 2 keyboard on isa0060/serio0
atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, m
ight be trying access hardware directly.
ReiserFS: hde5: Using r5 hash to sort names
input: AT Translated Set 2 keyboard on isa0060/serio0
hdg: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdh: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
FDC 0 is a post-1991 82077
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, l
ow) -> IRQ 11
eth0: VIA Rhine II at 0xdfffbd00, 00:0b:6a:6a:68:3a, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link
41e1.
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 3 (level, lo
w) -> IRQ 3
PCI: Setting latency timer of device 0000:00:11.5 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 3 (level, lo
w) -> IRQ 3
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 3, io mem 0xdfffbe00
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2
004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, l
ow) -> IRQ 11
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 C
ontroller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000c800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, l
ow) -> IRQ 11
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 C
ontroller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000cc00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 10 (level, l
ow) -> IRQ 10
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 C
ontroller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 10 (level, l
ow) -> IRQ 10
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 C
ontroller (#4)
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000d400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-1: new low speed USB device using uhci_hcd and address 2
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ibm_acpi: ec object not found
input: USB HIDBP Mouse 1241:1111 on usb-0000:00:10.1-1
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
om
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
NTFS driver 2.1.22 [Flags: R/W MODULE].
NTFS-fs warning (device hde1): parse_options(): Option iocharset is de
precated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device hde: parse_options(): Option iocharset is de
precated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device hde9): parse_options(): Option iocharset is de
precated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device hde10): parse_options(): Option iocharset is d
eprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs warning (device hde11): parse_options(): Option iocharset is d eprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x77, irq 7, dma 0 [PCSPP,TRISTATE,COMP AT,EPP,ECP,DMA]
pnp: Device 00:02 disabled.
ieee1394: Initialized config rom entry `ip1394'
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
pnp: Device 00:02 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x77, irq 7, dma 0 [PCSPP,TRISTATE,COMP AT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
lp0: console ready
mtrr: 0xda000000,0x1000000 overlaps existing 0xda000000,0x400000 |
|
IP卡
狗仔卡
显身卡
发表于 2005-8-1 21:12:09
发表于 2005-8-1 23:38:49