各位兄弟请帮我看看,我是刚学LINUX,装无线网卡碰到困难.

dayerong

各位,我是刚开始学LINUX,看了网上介绍安装驱动,可就是看的和碰到的有差距.都不一样.我的笔记本装RH9.0 ,一块PC无线网卡,安装盘里有LINUX的驱动.
这是readme:
=======================================================================

        ATMEL PCMCIA PCI USB linux driver

=======================================================================



+---------------------+

|PART A. Instructions.|

+---------------------+

0.

--

        This is the first release of ATMEL's open source linux drivers and

        configuration and monitor utilities.

        Due to a reconstruction of the directory structure; the use of

        new Makefile and new configuration scripts this is an untested

        version. We will test it and any bug fixes will be committed in

        the CVS in atmelwlandriver.sourceforge.net .



1. Configuration.

--

        You can either run make config or bash scripts/Config.sh.

        You have to answer a few questions and a .config file will be created.



2. Build and installation

--

        If a .config file exists then you need the following step:



        # make install



        to build and install the drivers you need.

        Remember to login as root before installing the drivers.



3. RF Board Type?

--

        There are several Atmel chips for PCMCIA and USB which can be combined with

        a bunch of RF boards.

        If you don't know what is the exact type of the board:

        a. Just build and install everything.

        b. Plug you PCMCIA or USB board in and look in /var/log/messages for more info

           Then consult the following table.



                USB (the product IDs below are Atmel's ones only !):



                   PID       | Atmel chip | RF board | driver

                ----------+------------+----------+--------

                7603      |       503A |     3861 | usbvnet.o

                7604      |       503A |     3863 | usbvnet3.o

                7605      |       503A |     RFMD | usbvnetr.o

                7606      |       505  |     RFMD | usbvnet5.o



                ( The 505 is currently not supported due to missing firmware.)



                If no driver is loaded on plugging your USB adapter, check if the (vendor ID,product ID)

                pair is already contained in any of the *_DEVICES defines in src/includes/usb/config.h.

                If yes, build a driver for this RF board and try again.

                If no, try to find out which RF board your adapter contains (look inside, check the FCC

                pictures of the device, or try out all RF boards). Add your product / vendor ID pair in

                the appropriate *_DEVICES define in the config.h file. Build and install again.

                On success, please notify the developers at sourceforge to include the new IDs.



                PCMCIA :



                    ID           | DRIVER

                -------------+---------------

                    AT76C502     | PCMCIA Intersil

                AT76C502AR   | PCMCIA RFMD

                AT76C502AR_D | PCMCIA RFMD revision D

                AT76C502AR_E | PCMCIA RFMD revision E

                AT76C504     | PCMCIA RFMD 504



         c. If you cannot find your device's ID in the above table's than try to get the

                 required information from the Manufacturer....



4. TOOLS

--

        In order to use the ncurses based command line (lvnet) and the X windows (xvnet) applications

        you must enable the

                Wireless LAN (non-hamradio)

        option inside the kernel (and of course if it was disabled to rebuild your kernel).

        For help regarding the two tools try the corresponding man pages.



        Alternatively: Get the wireless tools (iwconfig et al) and use them.

       

5. Support.

--

        For any questions use the sourceforge project's mailing list:

        [email protected]



+--------------------+

|PART B. Known Issues|

+--------------------+

        USB driversSTART)

        ------------

        The URB's going to the device are using the

        Adapter->devreq->length field which on some platforms can cause

        serious problems. This will be fixed very soon.



        There is also a report for a deadlock in the initialization routine. We cannot

        reproduce it so far.



        There is a serious "conflict" with the usb-uhci driver and atmel's board which

        leads to one problem. The system hangs      .....

        This never happens with the uhci driver.



        USB driversEND)

        -----------------



+------------+

|PART C. TODO|

+------------+



        Add support for different product and vendor ID's....







然后我似乎是照着一样作的:
[root@localhost Linux]# make config
make: *** Warning: File `Makefile' has modification time in the future (2002-09-03 18:20:58 > 2000-01-01 21:52:53.014923)
make: execvp: scripts/Config.sh: 权限不够
make: *** [config] Error 127

或:
[root@localhost Linux]# make
make: *** Warning: File `Makefile' has modification time in the future (2002-09-03 18:20:58 > 2000-01-01 21:54:09.12847)
Pick one of the following targets:
        make clean              - Remove object files and .config
        make config             - Configure and check system setup
        make install            - Build your system configuration, install modules and programs
make: warning:  Clock skew detected.  Your build may be incomplete.
[root@localhost Linux]# make install
make: *** Warning: File `Makefile' has modification time in the future (2002-09-03 18:20:58 > 2000-01-01 21:54:20.453817)
find -name '*.o' -o -name '*.map' |xargs rm -f
make: execvp: scripts/Config.sh: 权限不够
make: *** [config] Error 127

不知道怎么回事? 请各位好心帮我看看.真的谢谢.

dayerong

真的帮我看看,到底应该怎么装才对,谢谢各位了~~~