help：skyeye 下运行 uclinux 出错

greysun

编译成功可后，我用skyeye运行时出错，不知到那里配置不对 。


[root@greysun images]# skyeye linux
***********************************************************************
****                                                               ****
****   SkyEye  Simulator Ver 0.9.8 with  GDB/Insight 5.3 Interface ****
****                                                               ****
***********************************************************************
GNU gdb 5.3
Copyright 2002 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB.  Type "show warranty" for details.
This SkyEye was configured as "--host=i686-pc-linux-gnu --target=arm-elf"...
(SkyEye) target sim
cpu info: armv3, arm7tdmi, 41007700, fff8ff00, 0
mach info: name s3c4510b, mach_init addr 0x8162474
SKYEYE: use arm7100 mmu ops
Loaded ROM   ./romfs.img
Connected to the simulator.
(SkyEye) load
Loading section .init, size 0x11000 vma 0x8000
Loading section .text, size 0x217a00 vma 0x19000
Loading section __ex_table, size 0x748 vma 0x230a00
Loading section __ksymtab, size 0x3280 vma 0x231148
Loading section __ksymtab_gpl, size 0x3f0 vma 0x2343c8
Loading section __ksymtab_strings, size 0x7568 vma 0x2347b8
Loading section __param, size 0xa0 vma 0x23bd20
Loading section .data, size 0x106f0 vma 0x23c000
Start address 0x8000
Transfer rate: 19015040 bits/sec.
(SkyEye) run
Starting program: /root/temp/uClinux-dist/images/linux
Linux version 2.6.10-hsc1 (root@greysun) (gcc version 3.4.0) #20 Thu Jun 8 18:57:08 CST 2006
CPU: Samsung-S3C4510B [36807001] revision 1 (ARMv4T)
Machine: ESPD 4510B(S3C4510B)
Warning: bad configuration page, trying to continue
Built 1 zonelists
Kernel command line: root=/dev/ram0 initrd=0x0015c200,850k keepinitrd
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 16MB = 16MB total
Memory: 13824KB available (2187K code, 135K data, 68K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
NET: Registered protocol family 16
NetWinder Floating Point Emulator V0.97 (double precision)
Initializing Cryptographic API
ttyS0 at I/O 0x3ffd000 (irq = 4) is a Samsung S3C4510B Internal UART
ttyS1 at I/O 0x3ffe000 (irq = 6) is a Samsung S3C4510B Internal UART
io scheduler noop registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Samsung S3C4510B Ethernet Driver version 0.2 (2004-06-13) <[email protected]>
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 204
NET: Registered protocol family 17
RAMDISK: romfs filesystem found at block 0
RAMDISK: Loading 850KiB [1 disk] into ram disk... done.
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 68K

Program received signal SIGINT, Interrupt.
0x00000000 in ?? ()
(SkyEye)