skyeye网络问题

asdfbbs

我使用ubuntu8.04，用的是ubuntu的skyeye, “apt-get install skyeye”安装的，skyeye版本好像是1.2，从网上下载的testsuit2.3，使用里面的linux/s3c2410/s3c2410x-2.6进行测试，目前遇到网络的问题，运行消息如下：见红色字，armlinux运行起来后，手工执行ifconfig eth0 up也会提示：
eth0: 10Base-T (RJ-45) has no cable
eth0: no network cable attached to configured media
请教这是为什么，该怎么办啊？

big_endian is false.
arch: arm
cpu info: armv4, arm920t, 41009200, ff00fff0, 2
mach info: name s3c2410x, mach_init addr 0x805f030
ethmod num=1, mac addr=0:4:3:2:1:f, hostip=10.0.0.1
lcd_mod:1
uart_mod:0, desc_in:, desc_out:, converter:
SKYEYE: use arm920t mmu ops
Loaded RAM   ./initrd.img
start addr is set to 0xc0008000 by exec file.
Linux version 2.6.14 (root@lee) (gcc version 3.4.6) #48 Sat Feb 10 06:29:17 CST 2007
CPU: ARM920Tid(wb) [41009200] revision 0 (ARMvundefined/unknown)
Machine: SMDK2410
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410 (id 0x32410000)
S3C2410: core 62.400 MHz, memory 62.400 MHz, peripheral 62.400 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: mem=32M console=ttySAC0 root=/dev/ram initrd=0xc0800000,0x00800000 ramdisk_size=2048 rw
PID hash table entries: 256 (order: 8, 4096 bytes)
timer tcon=00000000, tcnt cb1f, tcfg 00000200,00000000, usec 0000189e
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 22168KB available (1510K code, 373K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
softlockup thread 0 started up.
Freeing initrd memory: 8192K
NET: Registered protocol family 16
S3C2410: Initialising architecture
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c2800000, irq 33
DMA channel 1 at c2800040, irq 34
DMA channel 2 at c2800080, irq 35
DMA channel 3 at c28000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
ERROR: s3c2410x_io_write_word(0x4d000060) = 0x00000000
ERROR: s3c2410x_io_write_word(0x4d000050) = 0x00000000
[GTK_LCD]: Can't find LCD DMA from address 0x0
ERROR: s3c2410x_io_write_word(0x4d000060) = 0x00000000
ERROR: s3c2410x_io_write_word(0x4d000050) = 0x00000000
Console: switching to colour frame buffer device 40x29
fb0: s3c2410fb frame buffer device
S3C2410 RTC, (c) 2004 Simtec Electronics
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2410
ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2410
ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 2048K size 1024 blocksize
cs89x0:cs89x0_probe(0x0)
cs89x0.c: v2.4.3-pre1 Russell Nelson <[email protected]>, Andrew Morton <[email protected]>
eth0: cs8900 rev J found at 0xf4000300 [Cirrus EEPROM]
cs89x0 media RJ-45, IRQ 53, programmed I/O, MAC 00:04:03:02:01:0f
cs89x0_probe1() successful
cs89x0:cs89x0_probe(0x0)
cs89x0: request_region(0xf4000300, 0x10) failed
cs89x0: no cs8900 or cs8920 detected.  Be sure to disable PnP with SETUP
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 204
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 2048KiB [1 disk] into ram disk... done.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 100K
init started:  BusyBox v1.4.1 (2007-02-10 01:19:06 CST) multi-call binary
Starting pid 19, console /dev/console: '/etc/init.d/rcS'
eth0: 10Base-T (RJ-45) has no cable
eth0: no network cable attached to configured media
ifconfig: SIOCSIFFLAGS: Resource temporarily unavailable
Welcome to
     _      _____      __   __    _      _
    / \    /  __ \    /  \_/  \  | |    |_|                 
   / _ \   | |  | |  / /\   /\ \ | |     _ ____  _   _  _  _
  / /_\ \  | |__| | / /  \_/  \ \| |    | |  _ \| | | |\ \/ /
/ /___\ \ | |__\ \ | |       | || |___ | | |_| | |_| |/    \
/_/        \_\| |   \_\|_|       |_||_____||_|_| |_|\____|\_/\_/
           
ARMLinux for Skyeye
For further information please check:
http://www.skyeye.org/



BusyBox v1.4.1 (2007-02-10 01:19:06 CST) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/ash: can't access tty; job control turned off

ksh

目前已经经过测试的Linux网络版本：at91 + rtl8019和cs8900 + s3c2410  SkyEye需要用skyeye-1.2.4