请求诊断：USB ADSL上网问题。谢谢！

works · 发表于 2003-10-9 22:49:15

全向QL8410 USB ADSL（非路由），REDHAT 9.0
cxacru-2003-05-05-src.tgz
libusb-0.1.7-3.i386.rpm
linux-atm-2.4.1-1.i386.rpm
pppoe拨号，执行cxstart.sh后出项如下情况，一直没法解决，还望高手指点：
[root@localhost root]# cxsart.sh
bash: cxsart.sh: command not found
[root@localhost root]# cxstart.sh
>>> Inits Conexant AccessRunner <<<

>>> Loading firmware...
Conexant AccessRunner microcode upload program. 5/5/2003
Josep Comas <[email protected]>
Pascal Boucher <[email protected]>

Compiled for ADSL modem with VendorID = 0572 & ProductID = cafe
ADSL modem found!
Loading and sending /usr/sbin/cxinit.bin...
Firmware is sent!
Firmware version = 2.15f
MAC address = 00:07:53:00:09:29
Waiting ADSL line is up (until 90 seconds)...
...
ADSL line is up (Downstream 2624 Kbits/s, Upstream 640 Kbits/s)

>>> Loading driver...
Launching driver in normal mode...
Using /lib/modules/2.4.20-8/kernel/drivers/usb/cxacru.o

/usr/sbin/cxload.sh successful
Setting RFC1483/2684 bridged...
>>> Setting RFC1483/2684 bridged <<<

>>> Loading br2684 kernel module...

>>> Loading br2684ctl...
Incorrectly built binary which accesses errno, h_errno or _res directly. Needs to be fixed.
RFC1483/2684 bridge: Interface "nas0" created sucessfully
RFC1483/2684 bridge: Communicating over ATM 0.0.32, encapsulation: LLC
RFC1483/2684 bridge: Interface configured

>>> Activating interface...
SIOCSIFNETMASK: 无法指定被请求的地址

>>> Adding default route...
Usage: inet_route [-vF] del {-host|-net} Target[/prefix] [gw Gw] [metric M] [[dev] If]
   inet_route [-vF] add {-host|-net} Target[/prefix] [gw Gw] [metric M]
                           [netmask N] [mss Mss] [window W] [irtt I]
                           [mod] [dyn] [reinstate] [[dev] If]
   inet_route [-vF] add {-host|-net} Target[/prefix] [metric M] reject
   inet_route [-FC] flush    NOT supported
[root@localhost root]# [root@localhost root]# cxsart.sh
bash: [root@localhost: command not found
[root@localhost root]#

works · 发表于 2003-10-9 22:51:32

还有一次是这样的：

[root@localhost root]# cxstart.sh
>>> Inits Conexant AccessRunner <<<

>>> Loading firmware...
Conexant AccessRunner microcode upload program. 5/5/2003
Josep Comas <[email protected]>
Pascal Boucher <[email protected]>

Compiled for ADSL modem with VendorID = 0572 & ProductID = cafe
ADSL modem found!
Loading and sending /usr/sbin/cxinit.bin...
Firmware is sent!
Firmware version = 2.15f
MAC address = 00:07:53:00:09:29
Waiting ADSL line is up (until 90 seconds)...
...
ADSL line is up (Downstream 2816 Kbits/s, Upstream 640 Kbits/s)

>>> Loading driver...
Launching driver in normal + max speed mode...
Using /lib/modules/2.4.20-8/kernel/drivers/usb/cxacru.o

/usr/sbin/cxload.sh successful
Setting RFC1483/2684 routed...
>>> Setting RFC1483/2684 routed <<<

>>> Loading atmarpd...

>>> Creating interface...

>>> Activating interface...
SIOCSIFNETMASK: 无法指定被请求的地址

>>> Creating PVC...
usage: /usr/local/sbin/atmarp -a
   /usr/local/sbin/atmarp -c [[atm]N]
   /usr/local/sbin/atmarp -q ip_addr [qos qos_spec] [sndbuf bytes]
   /usr/local/sbin/atmarp -s ip_addr [itf.]vpi.vci [pcr value] [qos spec] [sndbuf bytes]
      [temp] [pub] [null]
   /usr/local/sbin/atmarp -s ip_addr atm_addr [pcr value] [qos spec] [sndbuf bytes] [temp]
      [pub] [arpsrv]
   /usr/local/sbin/atmarp -d ip_addr [arpsrv]
   /usr/local/sbin/atmarp -V
[root@localhost root]# cxstop.sh
Stopping RFC1483/2684 routed...
>>> Down RFC1483/2684 routed network interface <<<

>>> Shutting down atm0 interface...

>>> Killing atmarpd daemon...

>>> Stopping transfers...
Conexant AccessRunner ioctl call. 5/5/2003
Josep Comas <[email protected]>
Pascal Boucher <[email protected]>

Compiled for ADSL modem with VendorID = 0572 & ProductID = cafe
ADSL modem found!

>>> Remove cxacru/cxacrudbg driver <<<

>>> Removing USB controller...

>>> Removing cxacru driver...

>>> Loading again USB controller...

[root@localhost root]#

challenger · 发表于 2003-10-10 09:36:21

你设置了协议和VPI，VCI的值了吗？我用的是pppoa拨号，下面是我的配置文件，你参考一下。

/etc/cxacru
[code:1]#
# Config file for Conexant AccessRunner
#

# Driver mode
DRIVER_MODE=1  # 1 = normal, 2 = debug, 3 = normal+max speed (without ask adsl status), 4 = debug+max speed (w
ithout ask adsl status)

# Protocol
PROTOCOL_MODE=2  # 1 = RFC1483/2684 routed, 2 = PPP over ATM (pppoa), 3 = RFC1483/2684 bridged, 4 = PPP over E
thernet (pppoe)

# Paths
BINARY_PATH="/usr/sbin"
ATM_PATH=""

# ADSL
#  if OPEN_MODE is blank then cxload uses default mode acoording VID & PID
#  Values for OPEN_MODE are:
# 0 = auto selection, G.Handshake
# 1 = auto selection, T1.413
# 2 = G.Handshake
# 3 = ANSI T1.413
# 4 = ITU-T G.992.1 (G.DMT)
# 5 = ITU-T G.992.2 (G.LITE)
OPEN_MODE=

# ATM
VPI=0
VCI=35

# Specific for RFC1483/2684 routed/bridged
#  if IP_ADDRESS is blank in bridged mode then it uses DHCP to get IP
IP_ADDRESS=
NETMASK=255.255.255.0
GATEWAY=[/code:1]

/etc/ppp/chap-secrets
[code:1]# Secrets for authentication using CHAP
# client       server  secret                IP addresses
"*****"       *    "*****"    *[/code:1]

/etc/ppp/pap-secrets
[code:1]# Secrets for authentication using PAP
# client       server  secret                IP addresses
"*****"       *    "*****"    *[/code:1]

/etc/ppp/options
[code:1]lock
defaultroute
noipdefault
noauth
usepeerdns
sync
holdoff 4
persist
maxfail 25
passive
asyncmap 0
lcp-echo-interval 2
lcp-echo-failure 7
name hujian
user hujian
plugin /usr/lib/pppd/plugins/pppoatm.so
0.35[/code:1]

/etc/resolv.conf
[code:1]nameserver 202.99.192.66
nameserver 202.99.192.68[/code:1]

challenger · 发表于 2003-10-10 09:37:37

cxstart.sh
[code:1]>>> Inits Conexant AccessRunner <<<

>>> Loading firmware...
Conexant AccessRunner microcode upload program. 24/6/2003
Josep Comas <[email protected]>
Pascal Boucher <[email protected]>
Pawel Konieczny <[email protected]>

I found ADSL modem with VendorID = 0572 & ProductID = cb00
Loading and sending /usr/sbin/cxfirm4.bin...
Firmware is sent!
Setting configuration...
Waiting ADSL line is up (until 90 seconds)...
..........
ADSL line is up (Downstream 1088 Kbits/s, Upstream 576 Kbits/s)
>>> Loading driver...
Launching driver in normal mode...
Using /lib/modules/2.4.20-8/kernel/drivers/usb/cxacru.o

/usr/sbin/cxload.sh successful
Setting PPP over ATM...
>>> Setting PPPoA <<<

>>> Loading ppp_generic...

>>> Loading pppoatm...

>>> Activating send/receive data...
Conexant AccessRunner ioctl call. 16/6/2003
Josep Comas <[email protected]>
Pascal Boucher <[email protected]>
Pawel Konieczny <[email protected]>

I found ADSL modem with VendorID = 0572 & ProductID = cb00

>>> Loading pppd daemon...

/usr/sbin/cxnet2up.sh successful[/code:1]

works · 发表于 2003-10-10 13:59:08

谢谢你！！
协议和VPI，VCI都已经设置的了，在windows下我是pppoe拨号的，在Linux下自然也该是pppoe的吧？但是我就是不能成功，郁闷～
不过听说，完全安装后的成功的可能性要大一点，这说法对吗？我是定制安装的。

challenger · 发表于 2003-10-10 15:17:10

你确定是pppoe吗？先开始电信局的人告我说是pppoe协议，结果我一直用pppoe连接，始终不成功，最后，仔细看了windows下的协议，才知道用的是pppoa。

challenger · 发表于 2003-10-10 15:18:14

windows下pppoe和pppoa分的不是很清楚

再说了，你说你用pppoe，但我相信你肯定设错了，这是你的cxstart.sh启动的代码
[code:1]Setting RFC1483/2684 routed...
>>> Setting RFC1483/2684 routed <<<
[/code:1]

works · 发表于 2003-10-11 03:13:05

我不是很会看这个协议的，你看这个是吗

works · 发表于 2003-10-11 03:15:46

另外
1、关于usespace，它一般是br2684ctl.c或者br011220.c。但是怎么编译它呢，具体执行什么命令？“在终端执行cc -0 br2684ctl br*.c -latm将生成br2684ctl”我在执行这个命令之后怎么没有找到br2684ctl,它应该在哪里找到？
2、执行br2684ctl -c 0 -e 0 inf VPI.VCI时，这个-e 0怎么填写？说-e 0表示封装模式，那它是什么封装模式，到哪儿可以查到它？
谢谢！

works · 发表于 2003-10-11 03:17:31

还有。这个br2684ctl.c哪里有下的？

works · 发表于 2003-10-12 09:39:39

[code:1]>>> Loading br2684ctl...
/usr/sbin/br2684ctl: error while loading shared libraries: libatm.so.1: cannot open shared object file: No such file or directory[/code:1]

请教这是个什么错误？

		自动登录	找回密码
密码			注册

请求诊断：USB ADSL上网问题。谢谢！

本帖子中包含更多资源