|
|
楼主 |
发表于 2003-10-26 21:57:06
|
显示全部楼层
附：我的安装过程，当然还是没有实现拨号上网的目标，请斑竹指正！！！！！
3.我在http://www.linuxant.com/下载了一个驱动程序,安装如下:
[root@zsl hsfmodem]# rpm -ivh hsfmodem-6.03.00lnxt03091800free_k2.4.20_8-1rh.i686.rpm
warning: hsfmodem-6.03.00lnxt03091800free_k2.4.20_8-1rh.i686.rpm: V3 DSA signature: NOKEY, key ID 5dfbf7dc
Preparing... ########################################### [100%]
1:hsfmodem ########################################### [100%]
Conexant HSF softmodem driver, version 6.03.00lnxt03091800free
If you need license keys, assistance or more information, please go to:
http://www.linuxant.com/
When reporting a problem for the first time, please send
us the file generated by "hsfconfig --dumpdiag".
Pre-built driver modules that seem compatible with your system were found under
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8.
Automatically guessed region (using timezone): "CHINA"
Setting region for modem unit 0: "CHINA"
To change, use "hsfconfig --region" or "AT+GCI=<T35code>"
The current region can be displayed by entering "ATI9" in a terminal program.
Current parameters: ("hsfconfig --info")
Config for modem unit 0: /dev/ttySHSF0
Device instance: 0-PCI-14f1:2f00-13e0:8d8f
HW revision : Basic2 2.18 Standard DAA 3VoltsIA
HW profile name: hsfpcibasic2hsfi
Current region : CHINA (T.35 code: 0026)
The /dev/modem alias (symlink) points to /dev/ttySHSF0
This is the free version of the driver, limited to 14.4Kbps data only.
For 56K modem and FAX functionality, please upgrade to the full version
available from http://www.linuxant.com/
驱动安装成功,并且将/dev/modem 链接到/dev/ttySHSF0
4.执行"开始>系统工具>互联网配置向导>调置解调器连接>下一步",
却出现"redhat-config-network:在您的系统上没有发现调置解调器"
接下来出现调置解调器属性:"调置解调器设备","波特率","流程控制"等,其中"调置解调器设备"一项中竟然没"/dev/modem"一项.
5.我选了"/dev/ttyS0"项,然而又无法激活Modem.
以上暂且不提: 我打开kppp拨号程序,这里的设备属性中有"/dev/modem",我选上,然后"查询调置解调器"发现"调置解调器就绪",把我激动了
半天,然后把其它什么帐号密码一设,却发现一点"连接",出现信息"调置解调器没有响应!"
将设备换成"/dev/ttyS0"后,如上,也能检测到,但拨号连接时,出现"正在初始化调置解调器..."就没有下文了!
我将设备换成"/dev/ttyS1"后,也是如此!!!!!,设备换成"/dev/ttyS2"或设备换成"/dev/ttyS3"后"查询调置解调器"时就出现"调置解调器忙"的提示!
实在是没办法,我执行如下命令:
[root@zsl root]# modprobe /dev/modem
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ich.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ich.o: insmod /usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ich.o failed
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97via.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97via.o: insmod /usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97via.o failed
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ali.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ali.o: insmod /usr/lib/hsfmodem/modules/binaries/i686/rh/linux-2.4.20-8/hsfmc97ali.o failed
接着我用dmesg命令看有关信息,发现:
[root@zsl root]# dmesg
Linux version 2.4.20-8 ([email protected]) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Mar 13 17:54:28 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007ff8000 (ACPI data)
BIOS-e820: 0000000007ff8000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/
Initializing CPU#0
Detected 1007.420 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2011.95 BogoMIPS
Memory: 124692k/131008k available (1347k kernel code, 4908k reserved, 999k data, 132k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(TM) CPU 1000MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdb51, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-0 with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 4D040H2, ATA DISK drive
blk: queue c03c9f40, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG CD-ROM SC-152L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=4982/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 146k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,6): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 20246
ext3_orphan_cleanup: deleting unreferenced inode 20245
EXT3-fs: ide0(3,6): 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:07.3
PCI: Sharing IRQ 5 with 00:07.2
usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Adding Swap: 393552k swap-space (priority -1)
MSDOS FS: Using codepage 936
MSDOS FS: IO charset cp936
MSDOS FS: Using codepage 936
MSDOS FS: IO charset cp936
parport0: PC-style at 0x378 (0x77 [PCSPP,TRISTATE]
parport_pc: Via 686A parallel port: io=0x378
ip_tables: (C) 2000-2002 Netfilter core team
Via 686a/8233/8235 audio driver 1.9.1-ac2
PCI: Found IRQ 10 for device 00:07.5
PCI: Sharing IRQ 10 with 00:07.6
PCI: Sharing IRQ 10 with 00:10.0
PCI: Setting latency timer of device 00:07.5 to 64
ac97_codec: AC97 Audio codec, id: ICE17 (ICE1232)
via82cxxx: board #1 at 0xD800, IRQ 10
Enabled Via MIDI
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
PCI: Found IRQ 10 for device 00:10.0
PCI: Sharing IRQ 10 with 00:07.5
PCI: Sharing IRQ 10 with 00:07.6
ttySHSF0 at I/O 0xc000 (irq = 10) is a Conexant HSF softmodem
PCI: Found IRQ 10 for device 00:07.6
PCI: Sharing IRQ 10 with 00:07.5
PCI: Sharing IRQ 10 with 00:10.0
PCI: Setting latency timer of device 00:07.6 to 64
cnxthsf_cnxt_serial_add: ComCtrlOpen failed (1) /* 请看这一句 */
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
特别是上面标明的一句:ComCtrlOpen failed (1) ,好像是说Com端口控制打开失败!!
my qq: 26165484 |
|
IP卡
狗仔卡
发表于 2003-10-25 22:17:06
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2003-10-26 19:41:34