slackware启动？

frizzly_hair

今天加了一个硬盘，现在是主盘windows2000，从盘linux，不过从盘上有一个fat32的分区，放了2k的页面文件，装完slackware9.1后，lilo装载mbr，启动时出错：
kmod:failed to exec /sbin/modprode -s -k ide-disk,errno = 2
vfs: can not open root device "1606" or "16:06"
please append a corrent "root=" boot option
kernel panil: vfs: unable to mount root fs on 1606

以下是syslog&lilo.conf
# LILO configuration file
# generated by 'liloconfig'
#
# Start LILO global section
append="hdc=ide-scsi"
boot = /dev/hda
#compact # faster, but won't work on all systems.
prompt
timeout = 50
map = /boot/System.map
# VESA framebuffer console @ 1024x768x256
vga = 773
# Normal VGA console
# vga = normal
# VESA framebuffer console @ 1024x768x64k
# vga=791
# VESA framebuffer console @ 1024x768x32k
# vga=790
# VESA framebuffer console @ 1024x768x256
# vga=773
# VESA framebuffer console @ 800x600x64k
# vga=788
# VESA framebuffer console @ 800x600x32k
# vga=787
# VESA framebuffer console @ 800x600x256
# vga=771
# VESA framebuffer console @ 640x480x64k
# vga=785
# VESA framebuffer console @ 640x480x32k
# vga=784
# VESA framebuffer console @ 640x480x256
# vga=769
# ramdisk = 0 # paranoia setting
# End LILO global section
# DOS bootable partition config begins
other = /dev/hda1
label = Windows2000
table = /dev/hda
# DOS bootable partition config ends
# Linux bootable partition config begins
image = /boot/vmlinuz
root = /dev/hdc6
label = Linux
read-only # Non-UMSDOS filesystems should be mounted read-only for checking
# Linux bootable partition config ends

Linux version 2.4.22 (root@midas) (gcc version 3.2.3) #6 Tue Sep 2 17:43:01 PDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017ff0000 (usable)
BIOS-e820: 0000000017ff0000 - 0000000017ff3000 (ACPI NVS)
BIOS-e820: 0000000017ff3000 - 0000000018000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
383MB LOWMEM available.
On node 0 totalpages: 98288
zone(0): 4096 pages.
zone(1): 94192 pages.
zone(2): 0 pages.
Kernel command line: initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=6464 rw root=/dev/ram SLACK_KERNEL=bare.i BOOT_IMAGE=/kernels/bare.i/bzImage root=/dev/hdc6 noinitrd ro
Initializing CPU#0
Detected 1477.531 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2949.12 BogoMIPS
Memory: 383200k/393152k available (1813k kernel code, 9564k reserved, 614k data, 116k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383f9ff c1c3f9ff 00000000 00000000
CPU: Common caps: 0383f9ff c1c3f9ff 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb250, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3099] at 00:00.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-0 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 6464K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdcMA, hddMA
hda: ST3120022A, ATA DISK drive
blk: queue c03a9d80, I/O limit 4095Mb (mask 0xffffffff)
hdc: QUANTUM FIREBALLP AS40.0, ATA DISK drive
hdd: LITE-ON LTR-40125S, ATAPI CD/DVD-ROM drive
blk: queue c03aa1d4, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(100)
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=77557/16/63, UDMA(100)
hdd: attached ide-cdrom driver.
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
hdc: [PTBL] [4866/255/63] hdc1 < hdc5 hdc6 hdc7 hdc8 hdc9 > hdc2
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2118.800 MB/sec
32regs : 1213.200 MB/sec
pIII_sse : 3032.800 MB/sec
pII_mmx : 3460.000 MB/sec
p5_mmx : 4415.200 MB/sec
raid5: using function: pIII_sse (3032.800 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
FAT: bogus logical sector size 0
UMSDOS: msdos_read_super failed, mount aborted.
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide1(22,6)) ...
for (ide1(22,6))
ide1(22,6):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Adding Swap: 489940k swap-space (priority -1)
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide1(22,5)) ...
for (ide1(22,5))
ide1(22,5):Using r5 hash to sort names
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide1(22,7)) ...
for (ide1(22,7))
ide1(22,7):Using r5 hash to sort names
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide1(22,) ...
for (ide1(22,)
ide1(22,:Using r5 hash to sort names
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 32M @ 0xe8000000
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xe400, IRQ 11
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xe800, IRQ 11
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xd8b49000, 00:e0:4c:56:bb:04, IRQ 5
eth0: Identified 8139 chip type 'RTL-8139C'
eth1: RealTek RTL8139 Fast Ethernet at 0xd8b4b000, 00:e0:4c:a3:ea:d9, IRQ 11
eth1: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
出错处就是这里