怎么用make编译这个文件?(sis315显卡驱动)

cby

sis315 for Linux的官方驱动，我从sis的官方站点下载的。在sis650主板（集成sis315）安装无误。
1.cp sis_drv.o-410 /usr/X11R6/lib/modules/drivers/sis_drv.o

2.make sure /etc/X11/XF86Config file has the correct "driver" section.driver "sis"

3.startx.

为什么我执行第2步 不成功呢,说什么 sure 没这个 选项?

麻烦各位 帮帮我,我刚接触 linux

Ivn

看看你的 /etc/X11/XF86Config
[code:1]
Section "Device"
....
Driver    "sis"          <-------- 这里是否是 sis

....
EndSectiion
[/code:1]
//
startx

cby

谢谢斑竹这么快就回复!!!

在我的 XF86Config 里是这样的

Section "Device"
    Identifier        "Generic VGA"
    VendorName        "Unknown"
    BoardName "Unknown"
    Chipset   "generic"

#    VideoRam 256

#    Clocks   25.2 28.3

EndSection

# Device configured by Xconfigurator:

Section "Device"
    Identifier  "AOpen PA45"
    VendorName  "Unknown"
    BoardName   "Unknown"
    #VideoRam    32768
    # Option "no_accel" # Use this if acceleration is causing problems
    # Option "fifo_moderate"
    # Option "fifo_conserv"
    # Option "fifo_aggresive"
    # Option "fast_vram"
    # Option "pci_burst_on"
    # Option "xaa_benchmark" # DON'T use with "ext_eng_queue" !!!
    # Option "ext_eng_queue" # Turbo-queue. This can cause drawing
                             # errors, but gives some accel
    # Insert Clocks lines here if appropriate
EndSection


另外我发现在这个目录下还有一个 XF86Config-4 文件,里面的内容是这样的:

.
.
.
Section "Monitor"
        Identifier "CM777Z/CM787"
        VendorName "Unknown"
        ModelName  "Unknown"
        HorizSync 30 - 70
        VertRefresh 50 - 100
        Option "dpms"
EndSection

Section "Device"
        Identifier "AOpen PA45"
        Driver "sis"
        BoardName "Unknown"
    # Option "no_accel" # Use this if acceleration is causing problems
    # Option "fifo_moderate"
    # Option "fifo_conserv"
    # Option "fifo_aggresive"
    # Option "fast_vram"
    # Option "pci_burst_on"
    # Option "xaa_benchmark" # DON'T use with "ext_eng_queue" !!!
    # Option "ext_eng_queue" # Turbo-queue. This can cause drawing
                             # errors, but gives some accel
EndSection

Section "Device"
        Identifier "Linux Frame Buffer"
        Driver "fbdev"
        BoardName "Unknown"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device "AOpen PA45"
        Monitor "CM777Z/CM787"
        DefaultDepth 8
EndSection

Section "DRI"
        Mode 0666
EndSection

由于我是第一次弄 Linux ,所以我用 Xconfigurator 瞎弄了好几次,数据可能已经不对了!

另外我的显卡在 WIN XP 里测出来是 SIS 315 显存 是 64M
我装的是 Red Hat Linux 7.2

请继续给予帮助!!!再次感谢!!!

cby

我把 要改的地方 都改了,startx 黑屏了几秒 然后 又回到 字符状态了?这怎么办啊?

realwish

查我的帖子，有个非官方驱动的

cobranail

[quote:51165f8d9d="cby"]sis315 for Linux的官方驱动，我从sis的官方站点下载的。在sis650主板（集成sis315）安装无误。
1.cp sis_drv.o-410 /usr/X11R6/lib/modules/drivers/sis_drv.o

2.make sure /etc/X11/XF86Config file has the correct "driver" section.driver "sis"

3.startx.

为什么我执行第2步 不成功呢,说什么 sure 没这个 选项?

麻烦各位 帮帮我,我刚接触 linux[/quote]
我觉得你应该先补习一下英语

cby

你说的是这个吗?

http://www.winischhofer.net/linuxsisvga.shtml

cby

我知道了, 第2行 是说 确定XF86Config文件里的driver这一行是否有"sis"，没有的话可能要自己手工改!

但 到底 怎么改呢? 我现在是 一头雾水 !

cobranail

把完整的XF86Config和XF86Config－4贴出来……
更新内核……

cby

XF86Config 的内容如下:

# File generated by XConfigurator.

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath        "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.

    FontPath   "unix/:7100"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

    # Uncomment this to cause a core dump at the spot where a signal is
    # received.  This may leave the console in an unusable state, but may
    # provide a better stack trace in the core dump to aid in debugging
    #NoTrapSignals

    # Uncomment this to disable the &lt;Crtl&gt;&lt;Alt&gt;<BS> server abort sequence
    # This allows clients to receive this key event.
    #DontZap

    # Uncomment this to disable the &lt;Crtl&gt;&lt;Alt&gt;&lt;KP_+&gt;/&lt;KP_-&gt; mode switching
    # sequences.  This allows clients to receive these key events.
    #DontZoom

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol    "Standard"

    # when using XQUEUE, comment out the above line, and uncomment the
    # following line
    #Protocol   "Xqueue"

    AutoRepeat  500 5

    # Let the server do the NumLock processing.  This should only be
    # required when using pre-R6 clients
    #ServerNumLock

    # Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    #Xleds      1 2 3

    #To set the LeftAlt to Meta, RightAlt key to ModeShift,
    #RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt        Meta
    RightAlt        Meta
   ScrollLock      Compose
   RightCtl        Control

# To disable the XKEYBOARD extension, uncomment XkbDisable.

#    XkbDisable

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    XkbModel    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    XkbModel    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    XkbLayout   "de"
# or:
#    XkbLayout   "de"
#    XkbVariant  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    XkbOptions  "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    XkbRules    "xfree86"
#    XkbModel    "pc101"
#    XkbLayout   "us"
#    XkbVariant  ""
#    XkbOptions  ""

   XkbKeycodes     "xfree86"
   XkbTypes        "default"
   XkbCompat       "default"
   XkbSymbols      "us(pc101)"
   XkbGeometry     "pc"
   XkbRules        "xfree86"
    XkbModel        "pc101"
    XkbLayout       "us"
EndSection

# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/mouse"
    ZAxisMapping 4 5

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol        "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice

#    BaudRate        9600
#    SampleRate        150

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Emulate3Buttons
#    Emulate3Timeout    50

# ChordMiddle is an option for some 3-button Logitech mice

#    ChordMiddle

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "CM777Z/CM787"
    VendorName  "Unknown"
    ModelName   "Unknown"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   30 - 70

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50 - 100

# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.

# These two are equivalent

#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace

#    Mode "1024x768i"
#        DotClock        45
#        HTimings        1024 1048 1208 1264
#        VTimings        768 776 784 817
#        Flags                "Interlace"
#    EndMode

# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.

# 512x384 @ 78 Hz, 31.50 kHz hsync
Modeline "512x384"    20.160 512  528  592  640   384  385  388  404 -HSync -VSync
# 512x384 @ 85 Hz, 34.38 kHz hsync
Modeline "512x384"    22     512  528  592  640   384  385  388  404 -HSync -VSync

# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400"     25.175 640  664  760  800   400  409  411  450
# 640x400 @ 85 Hz, 37.86 kHz hsync
Modeline "640x400"     31.5   640  672 736   832   400  401  404  445 -HSync +VSync

# 640x480 @ 100 Hz, 53.01 kHz hsync
Modeline "640x480"     45.8   640  672  768  864   480  488  494  530 -HSync -VSync
# 640x480 @ 60 Hz, 31.5 kHz hsync
Modeline "640x480"     25.175 640  664  760  800   480  491  493  525
# 640x480 @ 72 Hz, 36.5 kHz hsync
Modeline "640x480"     31.5   640  680  720  864   480  488  491  521
# 640x480 @ 75 Hz, 37.50 kHz hsync
ModeLine  "640x480"    31.5   640  656  720  840   480  481  484  500 -HSync -VSync
# 640x480 @ 85 Hz, 43.27 kHz hsync

Modeline "640x480"     36     640  696  752  832   480  481  484  509 -HSync -VSync
# 800x600 @ 100 Hz, 64.02 kHz hsync
Modeline  "800x600"    69.65  800  864  928 1088   600  604  610  640 -HSync -VSync
# 800x600 @ 56 Hz, 35.15 kHz hsync
ModeLine "800x600"     36     800  824  896 1024   600  601  603  625
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600"     40     800  840  968 1056   600  601  605  628 +hsync +vsync
# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600"     50     800  856  976 1040   600  637  643  666 +hsync +vsync
# 800x600 @ 85 Hz, 55.84 kHz hsync
Modeline  "800x600"    60.75  800  864  928 1088   600  616  621  657 -HSync -VSync

# 1024x480 for certain Vaios
Modeline "1024x480"   65 1024 1032 1176 1344 480 491 493 525 -HSync -VSync

# 1024x768 @ 100Hz, 80.21 kHz hsync
Modeline "1024x768"   115.5  1024 1056 1248 1440  768  771  781  802 -HSync -VSync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768"    65    1024 1032 1176 1344   768  771  777  806 -hsync -vsync
# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768"    75    1024 1048 1184 1328   768  771  777  806 -hsync -vsync
# 1024x768 @ 76 Hz, 62.5 kHz hsync
Modeline "1024x768"    85    1024 1032 1152 1360   768  784  787  823
# 1024x768 @ 85 Hz, 70.24 kHz hsync
Modeline "1024x768"   98.9  1024 1056 1216 1408   768 782 788 822 -HSync -VSync

# 1152x864 @ 100 Hz, 89.62 kHz hsync
Modeline "1152x864"   137.65 1152 1184 1312 1536   864  866  885  902 -HSync -VSync
# 1152x864 @ 60 Hz, 53.5 kHz hsync
Modeline  "1152x864"   89.9  1152 1216 1472 1680   864  868  876  892 -HSync -VSync
# 1152x864 @ 70 Hz, 62.4 kHz hsync
Modeline  "1152x864"   92    1152 1208 1368 1474   864  865  875  895
# 1152x864 @ 78 Hz, 70.8 kHz hsync
Modeline "1152x864"   110   1152 1240 1324 1552   864  864  876  908
# 1152x864 @ 84 Hz, 76.0 kHz hsync
Modeline "1152x864"   135    1152 1464 1592 1776   864  864  876  908

# 1280x960 @ 60 HzModeline "1280x960"   108   1280 1376 1488 1800 960 961 964 1000 +HSync +VSync
# 1280x960 @ 85 HzModeline "1280x960"   148.5 1280 1344 1504 1728 960 961 964 1011  +HSync +VSync

# 1280x1024 @ 100 Hz, 107.16 kHz hsync
Modeline "1280x1024"  181.75 1280 1312 1440 1696  1024 1031 1046 1072 -HSync -VSync
# 1280x1024 @ 61 Hz, 64.2 kHz hsync
Modeline "1280x1024"  110    1280 1328 1512 1712  1024 1025 1028 1054
# 1280x1024 @ 70 Hz, 74.59 kHz hsync
Modeline "1280x1024"  126.5 1280 1312 1472 1696  1024 1032 1040 1068 -HSync -VSync
# 1280x1024 @ 74 Hz, 78.85 kHz hsync
Modeline "1280x1024"  135    1280 1312 1456 1712  1024 1027 1030 1064
# 1280x1024 @ 76 Hz, 81.13 kHz hsync
Modeline "1280x1024"  135    1280 1312 1416 1664  1024 1027 1030 1064
# 1280x1024 @ 85 Hz, 91.15 kHz hsync
Modeline "1280x1024"  157.5  1280 1344 1504 1728  1024 1025 1028 1072 +HSync +VSync

# 1400x1050 @ 60Hz, 65.8 kHz hsync
Modeline "1400x1050"  129   1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 70Hz, 76.8 kHz hsync
Modeline "1400x1050"  151   1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 75Hz, 82.3 kHz hsync
Modeline "1400x1050"  162   1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
# 1400x1050 @ 85Hz, 93.2 kHz hsync
Modeline "1400x1050"  184   1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync

# 1600x1200 @ 60Hz, 75.00 kHz hsync
Modeline "1600x1200"  162   1600 1664 1856 2160  1200 1201 1204 1250 +HSync +VSync
# 1600x1200 @ 70 Hz, 87.50 kHz hsync
Modeline "1600x1200"  189    1600 1664 1856 2160  1200 1201 1204 1250 -HSync -VSync
# 1600x1200 @ 75 Hz, 93.75 kHz hsync
Modeline "1600x1200"  202.5  1600 1664 1856 2160  1200 1201 1204 1250 +HSync +VSync
# 1600x1200 @ 85 Hz, 105.77 kHz hsync
Modeline "1600x1200"  220    1600 1616 1808 2080  1200 1204 1207 1244 +HSync +VSync

# 1800x1440 @ 64Hz, 96.15 kHz hsync
ModeLine "1800X1440"  230    1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
# 1800x1440 @ 70Hz, 104.52 kHz hsync
ModeLine "1800X1440"  250    1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync

# Low-res Doublescan modes
# If your chipset does not support doublescan, you get a 'squashed'
# resolution like 320x400.

# 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio
Modeline "320x200"     12.588 320  336  384  400   200  204  205  225 Doublescan
# 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio
Modeline "320x240"     12.588 320  336  384  400   240  245  246  262 Doublescan
# 320x240 @ 72 Hz, 36.5 kHz hsync
Modeline "320x240"     15.750 320  336  384  400   240  244  246  262 Doublescan
# 400x300 @ 56 Hz, 35.2 kHz hsync, 4:3 aspect ratio
ModeLine "400x300"     18     400  416  448  512   300  301  302  312 Doublescan
# 400x300 @ 60 Hz, 37.8 kHz hsync
Modeline "400x300"     20     400  416  480  528   300  301  303  314 Doublescan
# 400x300 @ 72 Hz, 48.0 kHz hsync
Modeline "400x300"     25     400  424  488  520   300  319  322  333 Doublescan
# 480x300 @ 56 Hz, 35.2 kHz hsync, 8:5 aspect ratio
ModeLine "480x300"     21.656 480  496  536  616   300  301  302  312 Doublescan
# 480x300 @ 60 Hz, 37.8 kHz hsync
Modeline "480x300"     23.890 480  496  576  632   300  301  303  314 Doublescan
# 480x300 @ 63 Hz, 39.6 kHz hsync
Modeline "480x300"     25     480  496  576  632   300  301  303  314 Doublescan
# 480x300 @ 72 Hz, 48.0 kHz hsync
Modeline "480x300"     29.952 480  504  584  624   300  319  322  333 Doublescan

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section "Device"
    Identifier        "Generic VGA"
    VendorName        "Unknown"
    BoardName "Unknown"
    Chipset   "generic"

#    VideoRam 256

#    Clocks   25.2 28.3

EndSection

# Device configured by Xconfigurator:

Section "Device"
    Identifier  "AOpen PA45"
    VendorName  "Unknown"
    BoardName   "Unknown"
    #VideoRam    32768
    # Option "no_accel" # Use this if acceleration is causing problems
    # Option "fifo_moderate"
    # Option "fifo_conserv"
    # Option "fifo_aggresive"
    # Option "fast_vram"
    # Option "pci_burst_on"
    # Option "xaa_benchmark" # DON'T use with "ext_eng_queue" !!!
    # Option "ext_eng_queue" # Turbo-queue. This can cause drawing
                             # errors, but gives some accel
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    # Use Device "Generic VGA" for Standard VGA 320x200x256
    #Device      "Generic VGA"
    Device      "AOpen PA45"
    Monitor     "CM777Z/CM787"
EndSection

# The 16-color VGA server

Section "Screen"
    Driver      "vga16"
    Device      "Generic VGA"
    Monitor     "CM777Z/CM787"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

# The Mono server

Section "Screen"
    Driver      "vga2"
    Device      "Generic VGA"
    Monitor     "CM777Z/CM787"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

# The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32, Mach64
# I128, and S3V)
Section "Screen"
    Driver      "accel"
    Device      "AOpen PA45"
    Monitor     "CM777Z/CM787"
EndSection

cby

XF86Config-4 的内容如下:

# XFree86 4.0 configuration generated by Xconfigurator

Section "ServerLayout"
        Identifier "XFree86 Configured"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

# By default, Red Hat Linux 6.0 and later use xfs

Section "Files"
        FontPath "unix/:7100"
EndSection

# Module loading section

Section "Module"
        Load  "dbe"                # Double-buffering
        Load  "GLcore"                # OpenGL support
        Load  "dri"                # Direct rendering infrastructure
        Load  "glx"                # OpenGL X protocol interface
        Load  "extmod"                # Misc. required extensions
        Load  "v4l"                # Video4Linux
        # Load  "pex5"                # PHIGS for X 3D environment (obsolete)
        # Load  "record"        # X event recorder
        # Load  "xie"                # X Image Extension (obsolete)
        # You only need the following two modules if you do not use xfs.
        # Load  "freetype"         # TrueType font handler
        # Load  "type1"                # Adobe Type 1 font handler
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "keyboard"
        Option      "XkbLayout"        "us"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Device" "/dev/mouse"
        Option      "Protocol" "PS/2"
        Option      "Emulate3Buttons" "off"
        Option      "ZAxisMapping" "4 5"
EndSection

Section "Monitor"
        Identifier "CM777Z/CM787"
        VendorName "Unknown"
        ModelName  "Unknown"
        HorizSync 30 - 70
        VertRefresh 50 - 100
        Option "dpms"
EndSection

Section "Device"
        Identifier "AOpen PA45"
        Driver "sis"
        BoardName "Unknown"
    # Option "no_accel" # Use this if acceleration is causing problems
    # Option "fifo_moderate"
    # Option "fifo_conserv"
    # Option "fifo_aggresive"
    # Option "fast_vram"
    # Option "pci_burst_on"
    # Option "xaa_benchmark" # DON'T use with "ext_eng_queue" !!!
    # Option "ext_eng_queue" # Turbo-queue. This can cause drawing
                             # errors, but gives some accel
EndSection

Section "Device"
        Identifier "Linux Frame Buffer"
        Driver "fbdev"
        BoardName "Unknown"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device "AOpen PA45"
        Monitor "CM777Z/CM787"
        DefaultDepth 8
EndSection

Section "DRI"
        Mode 0666
EndSection


-------------------------------------------------------------------------------------

另外我的内核 是 2.4.7

cby

我已经快崩溃了!已经弄了好几天了!

我把机器拆了,看了显卡 是 AGP 的 上面写着 AG315P-64

可能是 AGP 315 64M 的意思吧!

有没有人能 指导 我一下,那个关于 SIS 的驱动我也下了,也拷贝到指定的位置了,然后 怎么配置 XF86Config 啊? 帮帮我吧!最后能具体点!

cobranail

起作用的是XF86Config-4，把这一段注释掉：

Section "Device"
Identifier "Linux Frame Buffer"
Driver "fbdev"
BoardName "Unknown"
EndSection

把

Driver "sis"

改成

Driver "vesa

升级内核 ，如果不想自己编译，下载rh9的内核装上

cby

Thanks cobranail

还是不行!哎~~~~~~

Ivn

你的 XF86Config 和 XF86Config-4 文件中 [code:1] Section &quot;Screen&quot; [/code:1] 和
[code:1] DefaultDepth [/code:1] 和 [code:1] SubSection &quot;Display&quot; [/code:1] 设置的太混乱了吧？
//
你的显示器和显卡在 windows 下可以达到什么模式 ？
//
你用 xf86cfg 配置一下， 如果可以起动 X ， 那么不要将 xf86cfg 建立的配置文件覆盖
/etc/X11/XF86Config 文件， 另外保存，再修改，主要改一下 那个 [code:1]dirver[/code:1]
选项， 如果你的显示器可以上到 24bit + 1024x768 , 那么在
[code:1] Section &quot;Screen&quot; [/code:1] 里添加
[code:1] DefaultDepth 24 [/code:1]
大致像这样：
[code:1]
Section &quot;Screen&quot;
        Identifier &quot;Screen0&quot;
        Device     &quot;Card0&quot;
        Monitor    &quot;Monitor0&quot;
        DefaultDepth    24
        SubSection &quot;Display&quot;
                Depth     1
        EndSubSection
        SubSection &quot;Display&quot;
                Depth     4
        EndSubSection
        SubSection &quot;Display&quot;
                Depth     8
        EndSubSection
        SubSection &quot;Display&quot;
                Depth     15
        EndSubSection
        SubSection &quot;Display&quot;
                Depth     16
        EndSubSection
        SubSection &quot;Display&quot;
                Depth     24
               Modes           &quot;1024x768&quot; &quot;800x600&quot;
        EndSubSection
EndSection
[/code:1]

//
主要是先让你的 X 起来：)
//
另外 rh7.2 setup 中不是有个 X 配置吗 ？ 你用过吗？