我编译的内核与apt-get的内核都出了相同的问题，大家帮忙

flashmob

2.6.8是自己编译的：但出现了错误，以至无法上网。ifconfig看不到
eth0,ifconfig -a 可以看到eth0,但无法ifconfig eth0 up。反馈说资源或设备忙。
dmesg如下
。。。。
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
    ACPI-0352: *** Error: Looking up [\_SB_.LNKH] in namespace, AE_NOT_FOUND
search_node cff2b620 start_node cff2b620 return_node 00000000
    ACPI-1133: *** Error: [NULL NAME], AE_NOT_FOUND
    ACPI-0352: *** Error: Looking up [\_SB_.LNKH] in namespace, AE_NOT_FOUND
search_node cff2b600 start_node cff2b600 return_node 00000000
    ACPI-1133: *** Error: [NULL NAME], AE_NOT_FOUND
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI-0352: *** Error: Looking up [\_SB_.LNKH] in namespace, AE_NOT_FOUND
search_node cff2b620 start_node cff2b620 return_node 00000000
    ACPI-1133: *** Error: [NULL NAME], AE_NOT_FOUND
    ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0._PRT] (Node cff2b5e0), AE_NOT_FOUND
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:10.0[A]: no GSI
ACPI: PCI interrupt 0000:00:10.1[B]: no GSI
ACPI: PCI interrupt 0000:00:10.2[C]: no GSI
ACPI: PCI interrupt 0000:00:10.3[D]: no GSI
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
ACPI: PCI interrupt 0000:00:11.5[C]: no GSI
ACPI: PCI interrupt 0000:00:12.0[A]: no GSI
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
vesafb: probe of vesafb0 failed with error -6
Simple Boot Flag at 0x3a set to 0x1
audit: initializing netlink socket (disabled)
audit(1103791472.603:0): initialized
Installing knfsd (copyright (C) 1996 [email protected]).
udf: registering filesystem
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
lp: driver loaded but no devices found

。。。
ACPI: PCI interrupt 0000:00:10.0[A]: no GSI
uhci_hcd 0000:00:10.0: Found HC with no IRQ.  Check BIOS/PCI 0000:00:10.0 setup!
ACPI: PCI interrupt 0000:00:10.1[B]: no GSI
uhci_hcd 0000:00:10.1: Found HC with no IRQ.  Check BIOS/PCI 0000:00:10.1 setup!
ACPI: PCI interrupt 0000:00:10.2[C]: no GSI
uhci_hcd 0000:00:10.2: Found HC with no IRQ.  Check BIOS/PCI 0000:00:10.2 setup!
usbcore: registered new driver usblp
还有一堆的
Losing some ticks... checking if CPU frequency changed.
Losing some ticks... checking if CPU frequency changed.
Losing some ticks... checking if CPU frequency changed.
Losing some ticks... checking if CPU frequency changed.
Losing some ticks... checking if CPU frequency changed.
Losing some ticks... checking if CPU frequency changed.

但网卡这部分看上去却好像没什么问题：
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A]: no GSI
eth0: VIA Rhine II at 0xb400, 00:0c:6e:11:c8:4c, IRQ 0.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.

flashmob

问题解决了，hoho

换了APM把ACPI给拿掉就好了